Cyrus CD i Kullanıcı Talimatları - Sayfa 12

Stereo sistemi Cyrus CD i için çevrimiçi göz atın veya pdf Kullanıcı Talimatları indirin. Cyrus CD i 15 sayfaları. Hi-fi
Ayrıca Cyrus CD i için: Kullanıcı Talimatları (18 sayfalar)

Sayfayı Yazdır
Cyrus CD i

learning TV and Satellite commands

In addition to controlling Cyrus components, the remote control can
learn the commands from two other remote control handsets. These will
normally be a TV and a Satellite or terrestrial TV set-top box, programmed
to the TV and SAT buttons, but could also be other audio components
including a Cyrus tuner or DVD player etc.
All keys may be programmed with the exception of the groups marked
CONTROL and SOURCE and the SETUP key.

Preparation for learning:

Check the following points before attempting to learn any commands -
•
Check that both remote controls have fresh batteries.
•
Choose a location on a tabletop that is not brightly lit. Subdued light
is better, away from bright natural or indoor lighting.
•
Check that you have enough time to spare to complete the learning
process for all the keys you want to use.

learning commands:

In this example, the Cyrus remote control will be learning commands
from a 'reference' Satellite receiver remote control.
1.
Set the two remote controls up facing each other, spaced by about
5cm.
2.
Press the TV or SAT
key to select the
mode that you want
to program.
The keypad will light and the key you selected will be red.
3.
Press and hold the
SETUP key.
The mode key will change to white. After about three seconds, the mode
key will light red again. This indicates that the remote control is ready to
learn codes.
4.
Release the SETUP key.
The remote control is now waiting to learn commands. The keypad will
light continually and the mode key will light pale red.
CONTROL
TV
SAT
SOURCE
ENTER
SELECT
TEXT
5cm
MENU
CONTROL
TV
SAT
SOURCE
1
2
3
abc
def
4
5
6
ghi
jkl
mno
7
8
9
pqrs
tuv
wxyz
0/10
STORE
ENTER
TV/AV
SELECT
SETUP
LIST
TEXT
MENU
3
1
2
abc
def
4
5
6
5.
On the reference remote control, press and hold the first key you
want to learn (for example, volume up) until the mode key flashes
red.
This indicates that the command has been received.
6.
Release the key on the reference remote control.
7.
Press a key on the Cyrus remote control (volume up in this example)
to select where you want to save that command.
The mode key will stop flashing. This indicates that the command has
been saved successfully.
If the learning process was successful, the remote control will be ready
to learn the next command.
8.
Repeat steps 5 to 7 for each command you want to learn.
When you have completed learning all commands -
•
Press the SETUP key.
The mode key will change to white. After a few seconds the backlight
will switch off.

Checking programmed commands:

•
Select the mode that you just programmed and check that the
commands were learned successfully.
NOTE: The TV or SAT mode key should flash red when sending a
command. If the mode key is not flashing, then the command has not
learned correctly.
•
Make a note of any commands that have not programmed correctly
and repeat the learning process to add these in.
CH
NOTE: When you start the learning process it does not erase any
programmed keys so you can re-program individual keys if required.

Problems with learning:

If none of the commands have learned correctly, try re-starting the
learning process again. Test a few keys first to ensure that your handset
is compatible for learning. If the test works then continue to program the
rest of the commands you need.
If you still have problems, check carefully that the mode light is flashing
correctly as you send a command to learn. If not, it may be that the
batteries need replacement in the reference handset or that the spacing
between the handsets is not ideal. Try adjusting the spacing between the
handsets and repeating the learning process.
If you continue to have problems, it may be that your handset is
incompatible with the learning process. This could happen with an older
design of handset or one that has an unusual code-set.

Sending TV or SAT commands

Once you have programmed all the keys with the commands you want,
you can use the remote control to send commands to your TV or Satellite
receiver etc.
•
Press the TV or SAT key to select the mode you want.
•
Press the command key.
The mode key will flash red when sending a programmed command.
CH
10
User Instructions