Asko D1876 Hızlı Başlangıç Kılavuzu - Sayfa 2

Bulaşık Makinesi Asko D1876 için çevrimiçi göz atın veya pdf Hızlı Başlangıç Kılavuzu indirin. Asko D1876 2 sayfaları. User manual use & care guide general fr (french version)
Ayrıca Asko D1876 için: Kullanım ve Bakım Kılavuzu (12 sayfalar), Kullanım ve Bakım Kılavuzu (12 sayfalar), (İspanyolca) Uso Y Cuidado (12 sayfalar), (Fransızca) Manuel D'utilisation Et D'entretien (12 sayfalar)

Sayfayı Yazdır
QUICK START PROCEDURES
QUICK START PROCEDURES
1.
Load the dishwasher. (There's no need to pre-rinse. Simply scrape off large food particles before you
load the dishes.)
2.
After you've pushed the baskets back inside the unit, manually rotate the upper and lower spray arms
to be sure they turn freely. Rearrange any item that blocks the wash arms.
3.
Make sure there is rinse aid in the dispenser. Add rinse aid, if needed.
4.
Add automatic dishwashing detergent and close the dispenser cover. (See "Amount of Dishwashing
Detergent to Use" below.)
5.
Close the door securely. (You should hear it click shut.)
6.
Press the touchpad for the desired program and options. The red indicator light for the program and
options selected will come on.
7.
Press Start. The dishwasher will start.
AMOUNT OF DISHWASHING DETERGENT TO USE
AMOUNT OF DISHWASHING DETERGENT TO USE
We recommend that you use only unscented, granular automatic dishwashing detergent. Generally, one tablespoon of detergent is
needed for a normal wash load. More heavily soiled items, however, may need more detergent. Also, the amount of detergent needed
can vary due to differences in water hardness. The harder the water, the more detergent you may need. (See page 5.) In any case, you
should never use more than three tablespoons of detergent.
LED WINDOW DISPLAYS
LED WINDOW DISPLAYS
Temperature Settings
Temperature Settings
The wash programs (except Rinse) have water temperature options, as
shown in the table to the right. The LED displays the temperature
selections in degrees Celsius. The table gives both the Celsius and
Fahrenheit temperatures. Once you select a temperature, it will remain
selected until you change it (except the Quick wash programs, which
reverts to 130° F). We recommend that you use the lower temperature
settings whenever possible to conserve energy.
Program Time
Program Time
When a program starts, the LED displays the time it took that program to run last time. As the program runs, the LED displays the
remaining time. If the time exceeds an hour, the display alternates between the hour and minutes remaining. The hour is designated by
an h (e.g., 1h).
The program times may not always be the same because of variations in the household hot water temperature. The dishwasher heats
the water to the proper temperature for the program selected, so if the temperature of the water entering your dishwasher is too low, the
dishwasher will run longer because it takes longer to heat the water. Raising your water heater setting could help to shorten the cycle
times. If this doesn't help, call the ASKO Advisory Center.
Delay Time
Delay Time
If you select the Delay option, the LED window displays "5h." To cancel delay, press the Delay touchpad until the LED displays zero.
Fault Codes
Fault Codes
The LED window displays three fault codes, as illustrated below.
Indicates a fault in the heater. Call your local service
technician.
Indicates high water level in the machine. Call the
ASKO Advisory Center.
UNDERSTANDING THE INDICATOR LIGHTS
UNDERSTANDING THE INDICATOR LIGHTS
When the dishwasher has finished, all of the indicator lights will come on. The lights will remain on until you open the door. When you
open the door, the indicator light for the wash program you last used will come on. If you used the high temperature options and the
heat dry option, those lights will come on, too.
If all of the lights on the control panel flash in sequence, this means the machine has detected an overfill. (See page 7.) Should this
happen, call the ASKO Advisory Center.
COMMONLY ASKED QUESTIONS
COMMONLY ASKED QUESTIONS
1)
Why does my dishwasher run so long?
2)
How do I know when the dishwasher is done?
3)
Why do all of the lights stay on?
4)
Why are all of the lights flashing?
5)
Why is there always water left in the bottom of my machine?
Wash Program
Pots & Pans/Sani
55° C (130° F)
Normal
55° C (130° F)
Quick
45° C (110° F)
Indicates a thermistor fault (heater control). Call your local
service technician.
This simply means the door isn't closed completely.
WHERE TO FIND THE ANSWERS
WHERE TO FIND THE ANSWERS
1)
See page 8 in the Use and Care Guide.
2)
See "Understanding the Indicator Lights" above.
3)
See "Understanding the Indicator Lights" above.
4)
See "Understanding the Indicator Lights" above.
5)
See page 9 in the Use and Care Guide.
Refer to this page in
the Use & Care Guide.
3, 4
3
5, 6
4, 5
Temperature Options
70° C (160° F)
65° C (150° F)
55° C (130° F)
Art. No. 80 731 01 rev01