Asko D3122 Kurulum Talimatları Kılavuzu - Sayfa 4

Bulaşık Makinesi Asko D3122 için çevrimiçi göz atın veya pdf Kurulum Talimatları Kılavuzu indirin. Asko D3122 12 sayfaları. D3122 use & care guide fr (french ucg 2+1 warranty)
Ayrıca Asko D3122 için: Kullanım ve Bakım Kılavuzu (16 sayfalar), Hızlı Başlangıç Kılavuzu (2 sayfalar), (İspanyolca) Uso Y Cuidado (16 sayfalar), (Fransızca) Kullanım Kılavuzu (16 sayfalar)

Sayfayı Yazdır

CORNER INST

CORNER INSTALLA

CORNER INST

If the dishwasher is installed in a corner, there must be

a minimum clearance of 2" (50 mm) from the side wall

so the door can open.

2" clearance

W W W W W A A A A A TER SUPPL

TER SUPPL

TER SUPPLY Y Y Y Y

TER SUPPL

WARNING! Plumbing connections must comply with

applicable sanitary, safety and plumbing codes in your

area.

The machine can be connected to either a hot or cold

water supply. If a cold water supply is used, the washing

times will be longer but the performance will not be

affected.

The dishwasher comes with a 6-foot PEX water supply

line that has a 3/8" NPT female connection.

E E E E E

I I I I I

ASY

NST

NSTALL

NST

ALL

ASY

NST

ALL

PEX tubing with 3/8"

compression fitting

PEX tubing has a 95-year

spec life. Fits American

dishwasher water supply

valves.

Drain hose boot

Ready to be cut to desired

drain connection. Only

one clamp required.

Electrical cord

110-120 volts, 15/20 amp

cord supplied with unit.

WARNING!

Do not use an extension cord for this appliance.

Page 4

ALLATION

ALLA

TION

CONNECTIONS

INST

INSTALLING

INST

ALLING

ALLING THE

THE TIP GU

THE

(OPTIONAL)

When it is not possible to fasten the dishwasher to the

cabinet, you should install tip guards to prevent the

machine from tipping when the door is opened. The tip

guards can be attached either to the floor or the wall.

The tip guards should be mounted behind the machine,

19" (483 mm) apart (measuring center to center) and

18-1/2" (470 mm) from the front of the machine. (Note:

This measurement could vary, depending on the

thickness of the custom panel, if any.)

Rear

We recommend that you install tip

guards when it isn't possible to fasten

the dishwasher to the cabinet.

After determining where the water supply line will enter

under the sink, drill a 1-1/2" (38 mm ) access hole and

run the line to the approximate inlet valve location shown

in the figure below. The water line inlet valve is on the

right rear of the machine.

For service convenience, a shut-off valve (not supplied)

should be installed in the supply line in an easily

accessible location, such as, beneath the sink.

It is important that the water supply line and the shut-off

valve have a sufficient flow volume. At last 3 gallons (12

liters) per minute must be able to pass through the

line. The water pressure should be 18-176 psi.

WARNING!

In order to prevent heat damage to the inlet valve, all

solder connections must be made before the water

line is connected to the dishwasher.

(1) Water supply

(2) Water supply valve

(not supplied)

Be sure to run the PEX tubing through the hole

NOTE:

to sink compartment before moving the

dishwasher into position.

TIP GUARDS

TIP GU

ARDS

Tip Guards

(P/N 8070851)