Asko T731 Kullanım ve Bakım Kılavuzu - Sayfa 6
Kurutucu Asko T731 için çevrimiçi göz atın veya pdf Kullanım ve Bakım Kılavuzu indirin. Asko T731 20 sayfaları. User manual use & care guide fr
Ayrıca Asko T731 için: Hızlı Başlangıç Kılavuzu (2 sayfalar), Planlama ve Tasarım Kılavuzu (19 sayfalar), Kullanım ve Bakım Kılavuzu (20 sayfalar), (İspanyolca) Kullanım ve Bakım Kılavuzu (20 sayfalar), (Fransızca) Manual D'utilisation Et D'entretien (20 sayfalar)
Sayfayı Yazdır
ELECTRICAL CONNECTIONS
The power supply cord must be grounded. If the machine
is to be used in a wet area, the supply must be protected
by a residual current device.
NOTE: In Canada, the dryer is delivered ready-fitted with
a four-prong plug intended for connection to a single-
phase supply.
CONNECTING A 3-WIRE POWER CORD
WARNING!
Before starting this procedure, be
sure the power is turned off at the breaker/fuse box.
Power Supply Cord
You will need a 3-wire power supply cord with three No.
10 copper wires and a matching 3-wire receptacle of
NEMA Type 10-30R, as illustrated below:
3-WIRE CORD
This blade connects
to this conductor.
Neutral
3/4" UL-listed
strain relief
CONNECTING A 4-WIRE POWER CORD
WARNING!
Before starting this procedure, be
sure the power is turned off at the breaker/fuse box.
Power Supply Cord
You will need a 4-wire power supply cord with four No. 10
copper wires and a matching 4-wire receptacle of NEMA
Type 14-30R, as illustrated below. The fourth wire must
be identified with a green cover and the neutral conductor
by a white cover.
4-WIRE CORD
3/4" UL-listed
Neutral
strain relief
Ground
prong
Page 6
Remove cover to
access terminal box.
(Requires a 20-Torx
screwdriver.)
Spade terminals
with upturned
Ring
terminals
Neutral
(white)
Spade terminals
with upturned
Ring
terminals
Neutral
(white)
Ground
(green)
Connection to a permanently wired supply point must be
made only by a qualified electrician.
As supplied:
Single-phase, 230 V, 60 Hz,
2500 Watt heater rating
30 A fuse required
WARNING:
The receptacle on the rear of the machine is
designed to accommodate ASKO washers ONLY
(rated 208–240 V.) To use this receptacle, you must
use the ready-fitted plug supplied with the washing
machine or an equivalent. The supply connection
must be 208–240 V, 20 A.
ASKO washers rated 208–240 V have two internal
fuses of 15 A each.
1.
Turn the power off at the breaker/fuse box.
2.
Remove terminal block cover.
3.
Use the strain relief attached below the terminal block
opening.
4.
Loosen or remove center terminal block screw.
5.
Connect neutral (white ) wire of power supply cord
to the center, silver-
colored terminal block
screw. Tighten the
screw.
6.
Connect the other
wires to outer screws.
7.
Tighten the strain relief
screws.
8.
R e p l a c e
t e r m i n a l
box cover on back of
dryer.
9.
Plug dryer into wall
receptacle.
10. Tu r n p o w e r o n a t
breaker/fuse box.
1.
Turn the power off at the breaker/fuse box.
2.
Remove terminal block cover.
3.
Use the strain relief attached below the terminal block
opening.
4.
Remove center terminal block screw.
5.
Remove ground wire
(green with yellow stripes)
from external ground
connector screw. Fasten
under center, silver-colored
terminal block screw.
6.
Connect ground (green) wire
of cord to external ground
conductor screw.
7.
Connect neutral (white) wire
of cord under center screw
of terminal block.
8.
Connect the other wires
to outer screws.
9.
Tighten the strain relief
screws.
10. Replace terminal box cover on back of dryer.
11. Plug dryer into wall receptacle.
12. Turn power on at breaker/fuse box.