Da-Lite Advantage Manual With CSR Інструкція з експлуатації - Сторінка 3
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Проекційний екран Da-Lite Advantage Manual With CSR. Da-Lite Advantage Manual With CSR 6 сторінок. Controlled screen return
Також для Da-Lite Advantage Manual With CSR: Інструкція з експлуатації (8 сторінок)
Друкувати сторінку
Screen and Roller Assembly Installation
for 60" to 96" Wide Screens
If your screen was shipped with the fabric and roller already
installed, skip this section.
1. Remove access door. First remove the 2 screws from the
ends (Figure 1). Be sure to support the door during this step
to avoid injury. Lift the door slightly and pull away from the
edge of the case.
2. Carefully unpack screen and roller assembly. Leave packing
paper on roller.
3. Loosen (but do not remove) two 1/4-20 nuts securing the
spring and dampener end bracket (stage left) to the case
housing. Slide the bracket towards the end of the case.
4. Insert the pin end of the roller (stage right) into the pin end
bracket. The mounting brackets have a formed tab that the
slat bar will rest against. Be sure to install the roller assembly
so the slat bar is positioned onto the tab. (Figure 2).
5. Slide the spring and dampener end bracket onto the square
end of the dampener assembly. Tighten the 1/4-20 nuts
securely.
6. Re-install the access door. Procedure is reverse of removal.
Screen and Roller Assembly Installation
for 100" to 164" Wide Screens
If your screen was shipped with the fabric and roller already
installed, skip this section.
1. Remove access door. First remove the 2 screws from the
ends (Figure 1). Be sure to support the door during this step
to avoid injury. Lift the door slightly and pull away from the
edge of the case.
2. Carefully unpack screen and roller assembly. Leave packing
paper on roller.
3. Loosen (but do not remove) two 1/4-20 nuts securing the pin
end bracket (stage left) to the case housing. Slide the bracket
towards the end of the case.
4. Insert the spring end of the roller into the spring end bracket.
The mounting brackets have a formed tab that the slat bar
will rest against. Be sure to install the roller assembly so the
slat bar is positioned onto the tab. (Figure 2).
NOTE: The spring end has a brass paw that catches on a
notch. This feature must be disabled on screens with CSR.
Make sure the notch is pointing down towards the
opening of the case.
5. Slide the pin end bracket onto the CSR pin. Tighten the
1/4-20 nuts securely.
6. Re-install the access door. Procedure is reverse of removal.
Operating 60" to 96" Wide Screens
1.
Pull down on pull bail until desired picture area is obtained.
Lock into position as on a window shade. Be sure surface is
locked before releasing.
2. To re-roll the screen, pull the picture surface down and start the
fabric up quickly and release.
Operating 100" to 164" Wide Screens
1.
Pull down on pull bail until desired picture area is obtained.
Lock into position as on a window shade. Be sure surface is
locked before releasing.
NOTE: this screen will not lock into position in the upper
portion of its travel.
2. To re-roll the screen, pull the picture surface down about 6 inches
and start the fabric up quickly and release.
Large picture surfaces are heavy and will start up too slowly to
prevent the locking pawl from catching unless help is provided.
If the locking pawl catches pull the picture surface down and
start the surface up rapidly.
The CSR feature of this screen will allow the fabric to retract
rapidly until about the last 6-12 inches of travel then it will slow
and retract gently into the case.
Remove 2 Screws
To Remove
Access Door
Slat Bar
Formed
Tab
Mounting
Bracket
Figure 1
Figure 2
3