Ekinex KNX EK-ED2-TP-RW Посібник із швидкого старту - Сторінка 4

Переглянути онлайн або завантажити pdf Посібник із швидкого старту для Контролер Ekinex KNX EK-ED2-TP-RW. Ekinex KNX EK-ED2-TP-RW 5 сторінок. Pushbutton

Друкувати сторінку

Warning! In order to supply the KNX bus lines use

only KNX bus power supplies (e.g. ekinex EK-AB1-

TP or EK-AG1-TP). The use of other power supplies

can compromise the communication and damage

the devices connected to the bus.

Bus

KNX

Configuration and commissioning

Configuration and commissioning of the device require

the use of the ETS

(Engineering Tool Software) program

V4 or later releases. These activities must be carried out

according to the design of the building automation system

done by a qualified planner.

Note. The configuration and commissioning of KNX

devices require specialized skills. To acquire these

skills, you should attend the workshops at KNX cer-

tified training centers.

Product

Application program

code

(## = release)

EK-ED2-TP

APEKED2TP##.knxprod

EK-E32-TP

APEKED2TP##.knxpro

Configuration

For the configuration of the device parameters the corre-

sponding application program or the whole ekinex

duct database must be loaded in the ETS program. For

detailed information on configuration options, refer to the

application manual of the device available on the website

www.ekinex.com.

Commissioning

For commissioning the device the following activities are

required:

• make the electrical connections as described above;

• turn on the bus power supply;

• switch the device operation to the programming mode

as described in the next table;

• download into the device the physical address and the

configuration with the ETS

At the end of the download the operation of the device

automatically returns to normal mode; in this mode the

programming LED (where available) and/or the LEDs of

the second color (for EK-ED2-TP-...) are turned off. Now

the bus device is programmed and ready for use.

Communica-

Group

tion objects

adresses

(nr. max)

229

254

229

254

pro-

program.

Product

code

version

04.xxx

and pre-

vious

from

05.xxx

06.018

EK-ED2-

06.019

and

later

EK-E32-TP

All

Reset of the device

To reset the device:

• if the programming button is present, remove the con-

nection to the bus network by extracting the bus ter-

minal from its seat. Keeping the programming button

pressed, reinsert the bus terminal in its seat; the pro-

gramming LED flashes quickly. Release the program-

ming button and extract the clamp again; the reset has

been performed.

• If, on the other hand, the programming button is not

present, repeat the programming sequence by holding

down the buttons for about 10 seconds. The LEDs of

the second color first flash, then go off; the reset has

been performed.

Warning! The reset restores the device back to the

state of delivery from the factory. The address and

the value of the parameters set during configuration

will be lost.

Programming

Visual

sequence

feedback

P r o g r a m -

Pressing the pro-

ming

gramming button

on steady.

Simultaneous press

of the first and last

button on the left

All LEDs of

side for 5 seconds.

the second

color flash.

P r o g r a m -

ming LED (if

present) on

steady.

Simultaneous pres-

sing of the first but-

ton on the left side

and the last button

on the right side for

5 seconds.

All LEDs of

the second

color flash.

P r o g r a m -

Pressing the pro-

ming

gramming button

on steady.

LED