DoorHan Sectional-1200 Посібник з монтажу та експлуатації - Сторінка 12
Переглянути онлайн або завантажити pdf Посібник з монтажу та експлуатації для Відкривач воріт DoorHan Sectional-1200. DoorHan Sectional-1200 16 сторінок.
Друкувати сторінку
1
ManUfacTUrer's WarranTy
Final Programming
(NB: This finalizing step must be carried out, otherwise the saved information
will be lost)
R
+
P
�
Programming of Transmitters
R
+
P
�
"0" will be shown on the
Press "S"
left side of the display,
and disappears immediately
At this time, the code isuccessfully set if opener works.
Other transmitters can be set as above.
all remote controls are entered one by one in the control unit. If the remote control is lost, delete radio codes and reprogram the remote controls
to prevent unauthorized access.
START
Before start make sure, that the system works without jamming (release the slide, open and close the gate manually)
remote control – opening, closing and stop are performed by pushing one button on the remote control unit.
manual control – in case of power cut, the gate can be controlled by hand after releasing the slide.
REPAIRS
If the gate requires repairs, contact the authorized centres doorHan.
MAINTENANCE
maintenance shall be carried out by the personnel, which was trained and certified at the authorized centre doorHan. replacement of fuses
shall be performed by the personnel, which is certified to perform electric operations.
the light lamp shall be replaced only after the operator is disconnected from mains.
the operator sectional-750 – is a mechanism, that requires minimal maintenance.
Check regularly mechanics of the gate (balance), the gate travel smoothness by automatic control.
Check regularly proper adjustment of extreme positions, functionality and capacity of safety devices. lubricate the moving parts.
In case of power cut you may need to restore operator's settings. For that, after restoration of power supply carry out one complete cycle of
opening/closing the gate:
after power cut the gate will stop.
after the power restoration, push the button on the remote control.
the gate will move up and stop in accordance with the programmed position.
Check functionality of the system at least every 6 months, pay special attention to the safety devices and the release.
DISPOSAL
Before disposal of the automatic system, remove and then dispose of the protective package of the operator! remember unutilized
package can be hazardous for people.
after expiration of life time, the item shall be delivered in a specialized disposal point!
MANUFACTURER'S WARRANTY
manufacturer's warranty is 3 years from the date of sale of the item.
the warranty does not cover the following cases:
•
Improper installation without following the recommendations of the manufacturer, which are specified in this manual.
•
performance of installation by the unqualified personnel, which was not certified at the authorized centre doorHan.
•
If the servicing was carried out in the centres, which are not authorized service centres doorHan.
•
unauthorized interference in the operator's adjustments, connection of accessories and disassembling.
•
Connection and use of accessories, produced by other manufacturers without agreement with the manufacturer.
•
other cases, provided for by the law of the country of the manufacturer.
12
I n s t a l l a t I o n a n d o p e r a t I n g m a n u a l s e C t I o n a l - 7 5 0 / 1 2 0 0
R
+
R
P
�
P
R
+
P
�
Press any key twice,
coding is completed.
Decode
R
+
P
�
+
Press & hold "R"
�
for 8 seconds
By now, no transmitters can operate the opener unless re�coded.
For security purpose if a transmitter has been lost the opener must be decoded
and the new transmitter encoded as above, so that the lost one
can not operate the door anymore.
R
+
R
P
P
�
Keep pressing the key
0" will be shown on the
until "0" disappeares
left side of the display.
+
�