DoorHan SLIDING-2100 Посібник з монтажу та експлуатації - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник з монтажу та експлуатації для Відкривач воріт DoorHan SLIDING-2100. DoorHan SLIDING-2100 12 сторінок. Drive
Також для DoorHan SLIDING-2100: Посібник з монтажу та експлуатації (16 сторінок), Посібник з монтажу та експлуатації (12 сторінок)
Друкувати сторінку
2. GENERAL SAFETY INSTRUCTIONS FOR INSTALLATION AND MAINTENANCE
•
For an efficient and safe automated door, correctly observe the installation procedures and instructions for use.
•
Incorrect installation and use can cause serious damage to persons and property.
•
Carefully read the whole installation manual before you begin installing.
•
do not make any modifications which are not mentioned in this manual.
•
do not install the operator for uses other than those indicated.
•
to fasten, use the supplied accessories or, in any case, fastening systems (screws, expansion plugs, etc.) suitable for the type of support
and for the mechanical stresses exerted by the automated system.
•
Check if the gate conforms to standards en12604 and en 12605 (the information can be found in the documentation accompanying the
gate itself). For non-eu countries, the above mentioned standards must be observed in addition to the national standard references to
obtain a suitable safety level.
•
Make sure that the gate is correctly operational, and supplied with mechanical opening stops.
When installing we advise you to:
•
obtain the material and tools indicated in the following paragraph "tools and materials" and keep them near at hand.
•
use a stable support for performing operations without a floor support.
•
protect your face and hands adequately before making the holes with the drill.
•
do not allow children to play near during installation, use and during the automated system release manoeuvre.
•
remove any debris and objects which could hamper movement, before powering up the system.
•
remove the gate's closing mechanism to ensure the gate is closed by the automatism.
•
stick on the warning stickers as shown in the instruction.
When you have finished installing we advise you to:
•
Make sure that no part of the gate interferes with public spaces such as pavements and/or roads.
•
use the automated system observing the instructions in the "user's guide".
•
Fill in, keep and update the maintenance register.
•
the slIdIng automated system does not require periodic replacement of parts.
•
every month, run a functional check of the safety devices.
If the power cable of operator slIdIng is damaged, it must be replaced by qualified personnel, using a new cable of the same type.
do not use different power cables.
3. TOOLS AND MATERIALS
tools you will require to install the slIdIng operator:
1.
set of flat wrenches for hexagon head screws
2.
set of screwdrivers for cross-head and cut-head screws
3.
set of wall bits
4.
set of iron bits
Material required for installing the SLIDING operator and the relevant accessories (if present):
•
Cable 2x0,5 mm2 (emitting photocells, pulse generators for opening movement and stop)
•
Cable 4x0.5 mm2 (receiver photocells)
•
Cable 2 x 1.5 mm2 (power)
•
use cables with an adequate degree of insulation.
the electric system must conform to the prescriptions in the chapter entitled "Warnings for the installer".
the 230 Vac power cable must be laid and connected by a qualified installation technician.
lay the cables in the appropriate pipes and do not allow loose cables to come into contact with moving parts of the
automated system and the gate.
3
GeneRAL sAFetY InstRUCtIons FoR InstALLAtIon AnD MAIntenAnCe
I n s t a l l a t I o n a n d o p e r a t I n g M a n u a l o p e r a t o r s l I d I n g - 1 3 0 0 / 2 1 0 0
5.
Flat-nose pliers
6.
saw on metal
7.
a hammer drill
8.
8. Folding rule (2 m)
3