DoorHan Transmitter 4 Посібник з монтажу - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник з монтажу для Пульт дистанційного керування DoorHan Transmitter 4. DoorHan Transmitter 4 2 сторінки.
Також для DoorHan Transmitter 4: Інструкція з програмування (2 сторінок), Посібник з монтажу (2 сторінок)
Друкувати сторінку
EC DECLARAtIon of ConfoRmItY
We: DoorHan Europe s.r.o.
Bozeny Nemcove 1689, 43201 Kadan, Ceska Respublika Herewith declare
under sole responsibility that:
Additional note:
These products have undergone tests in a typical uniform configuration
(all products manufactured by DoorHan Europe s.r.o.)
01/03/2010
1. DESCRIptIon
Remote control transmitters DoorHan are meant for DoorHan automat-
ics or any other device with the DoorHan radio receiver control. You can
control one or more (up to 4) different devices (gates, barriers etc.) with
the help of one transmitter.
2. tECHnICAL SpECIfICAtIonS
model
Battery
Working frequency
Quantity of channels
Working temperature range
3. pRogRAmmIng
programming of the remote controls with reciever DHRE-2
1) Before programming the former codes can be erased from the
memory of the recipient (it is recommended by the first setting). In order
to do that, hold down the key 10 sec (SW1 for connector CH1, SW2 for
connector CH2). The indicator LED1 will blink for 10 sec, then it will go out
for 2 sec and blink twice to confirm erasing of the codes.
2) To record the new code hold down for 3 sec the key «SW1» on the
recipient card, to make settings of the electric operator connected to the
output CH1 and the key «SW2» - to make settings of the electric operator
connected to the output CH2, at that the indicator LED1 will light. After
that press the necessary key on the remote control unit for 2-3 sec. At-
tention! after the operation is completed only one key can be stored in the
memory of the recipient.
3) To make settings for other remote controller repeat record proce-
dures with other remote controllers.
2
programming of the remote control units with build-in electric
operator SE-750(1200) reciever.
1) Before programming the former codes can be erased from the mem-
ory (it is recommended by the first setting). In order to do that, press and
hold down the key «R». The «0» will appear on the display. Hold down the
key «R» until the «0» disappears.
2) For each of the buttons there is a certain control channel (pic.),
which selection operation is described in Item 5 («Control key setting»).
The operator's default control button is key 1 or key 2 depending on the
controller's program.
3) To record the code of the remote controller press the key «R». On
the left part of the display the "0" will appear and disappear immediately.
Press the key on the remote controller twice.
4) Other remote control units are programmed in a similar way.
For removal of transmitter from memory of the receiver: Press and
keep during 8 with pressed button R, the indicator (zero in the bottom of
the display will not go out yet, the short sound signal will thus be distrib-
uted. For other information use the manual of door operator.
• Declares that:
The device model RCBLACK-4
• complies with the essential safety requirements of the
following directives:
73/23/EEC and subsequent amendment 93/68/EEC
89/336/EEC and subsequent amendment 92/31/EEC and
93/68/EEC
Mikhail Kiselev
1
InStALLAtIon mAnUAL
RCBLACK-4
-20 °С ... +50 °С
Managing Director
Date signature
RCBLACK-4
12V, type 27A
433,25 MHz
4
3
4