Air Doctor AD3000 Посібник користувача - Сторінка 5

Переглянути онлайн або завантажити pdf Посібник користувача для Очищувач повітря Air Doctor AD3000. Air Doctor AD3000 8 сторінок.

Друкувати сторінку
Air Doctor AD3000 Посібник користувача
OPERATING THE AIR DOCTOR
AD3000 AIR PURIFIER
Before first use, remove filters and remove plastic bag from filters, then reinstall filters.
Then reinstall front cover.
Plug the unit into an electrical outlet. The unit will be ready to run. Read the following directions
to select desired settings.

CONTROL PANEL

1
2
3
4
1.
Power Control
To operate the Air Doctor™, press the Power button to turn on the air purifier.
2.
Fan Speed Control
The Air Doctor™ has four different fan speed settings Low, Medium, High, and Boost. Each
mode has its own indicator light which lights up when the setting is chosen. The speed
selected determines how rapidly you want to clean the air. The "LOW" and "MEDIUM"
settings are great for everyday use. The "HIGH" setting is great for areas with more airborne
contaminants (such as excessive smoke, pet dander, etc), or areas used frequently by
allergy-sufferers. The "BOOST" setting is best used for shorter bursts of time when you
want to rapidly purify the air.
3.
Auto Mode
The Air Doctor™ is equipped with an air sensor to monitor the quality of your air. Simply
press the Auto button to activate the air monitoring system. The monitor will test the air
quality and automatically adjust the fan speed to remove the air contaminants. The front of
the display is equipped with LED lights to notify you of the air quality. RED color is for poor,
ORANGE for fair and BLUE for good quality air.
4.
Dim Mode
If the LED lights are too bright, activate the "Dim Mode" to turn off the LED lights and
the lighted display.
5.
Timer Control
The Air Doctor™ air purifier can be programmed to turn off after a preset amount of time.
Press the "TIME" button to program the timer. Each press will add one hour up to a total of 24
hours. Keeping the button pressed will automatically increase to 24 hours, 1 hour at a time.
6.
ION Generator
Press the ION button to turn on the IONs. Press it again to turn the IONs off.
7.
Clean Filter Indicator Light
The Air Doctor™ Clean Filter Indicator Light will turn on each time a filter needs to be
replaced. To reset the filter indicator, press the AUTO and DIM buttons together for 3 seconds.
The CLEAN FILTER light will flash 3 times and then turn off completely, indicating the unit has
been reset.
8.
24-Hour Timer Display
AD3000
™
5
6
7
AD3000
OPERATING THE AIR DOCTOR
AD3000 AIR PURIFIER
8

AIR QUALITY MONITOR

9.
Air Monitor
The Air Doctor™ comes with an Air Quality Monitor that continuously monitors the air.
The LED light located on the front will light up according to the air quality. The Air Quality
Monitor is able to show 3 air quality levels.
BLUE = Good air quality / ORANGE = Fair air quality / RED = Poor air quality
You can choose to set the Air Doctor™ to automatically adjust the Fan speed according to
the Air Quality. Simply push the "Auto" button located on the control panel. In Auto mode,
the fan speed will be adjusted as follows:
Good Air Quality = Low fan speed
Fair Air Quality = Medium fan speed
Poor Air Quality = High and Boost fan speed
Electrical Ratings
•
120 volt / 60 Hz
•
Power consumption / 95 watts
•
12 month Ultra HEPA filter
•
6 month Carbon filter
Replacment Filters
•
Ultra HEPA filter / ADF3001
•
Carbon filter / ADF3002
•
Pre-filter / ADF3003
To order replacement filters go to www.airdoctorpro.com or call 800.221.2515.
6
7
™
9