Canon IMAGE FORMULA DR-6010C Посібник з легкого старту
Переглянути онлайн або завантажити pdf Посібник з легкого старту для Сканер Canon IMAGE FORMULA DR-6010C. Canon IMAGE FORMULA DR-6010C 2 сторінки. Canon scanner user manual
Також для Canon IMAGE FORMULA DR-6010C: Брошура та технічні характеристики (26 сторінок), Брошура та технічні характеристики (4 сторінок), Посібник з очищення (8 сторінок)
Друкувати сторінку
Easy Start Guide
Thank you for purchasing the Document Scanner DR-6010C. The manuals for this scanner
include the Easy Start Guide (this manual) and Reference Guide (provided with the scanner,)
and the User Manual and CapturePerfect 3.0 Operation Guide (electronic manuals stored on
the setup disc.) Before using the scanner, read each manual throughly to familiarize youreself
with its capabilities, and to make the most of its many functions. After reading these manuals,
store them in a safe place for future reference.
Easy Start Guide (this manual)
Describes the procedures for setting up the scanner and instaling the
software. Follow the steps in this guide to set up the scanner quickly.
Reference Guide
Provides an overview of the most important features and points that the
user should know when using the scanner. For more details, refer to the
User Manual .
User Manual (electronic manual)
Consists of a "Hardware" volume and a "Software" volume.
The "Hardware" volume explains all topics related to handling and caring
for the scanner (i.e., setup, cleaning, maintenance, and troubleshooting.)
The "Software" volume explains the ISIS/TWAIN driver settings and Job
Registration Tool settings.
CapturePerfect 3.0 Operation Guide (electronic manual)
Explains the application that enhances the operation of all Canon
document scanners.
Note
The electronic manuals are PDF (Portable Document Format) files, and are installed
in the following folders during software installation. (
STEP 3)
User Manual
CapturePerfect 3.0 Operation Guide
Checking the Package Contents
When you unpack your scanner, make sure all of the following accessories are included.
If any of the items listed below are missing or damaged, contact your local authorized Canon
dealer or service representative.
Job Labels
DR-6010C
Power Cord
USB Cable
Easy Start Guide
Reference Guide
DR-6010C Setup Disc
Adobe Acrobat Setup Disc
(This Manual)
Warranty Card
Registration Card
Retard Roller
Roller Unit
Note
Items included in this package are subject to change without notice.
Keep the package and packing materials for storing or transporting the scanner.
After checking the package contents, you need to remove all the
packing materials protecting the scanner. (
STEP 2)
Trademarks
• Canon and the Canon logo are registered trademarks of Canon Inc. in the United States and may also be
trademarks or registered trademarks in other countries.
• imageFORMULA is a trademark of CANON ELECTRONICS INC.
• Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation
in the United States and/or other countries.
• Other brands and product names used in this manual may be trademarks or registered trademarks of their
respective companies.
PUB. CE-IE-717
© CANON ELECTRONICS INC. 2009
Removing the Packing Materials
After unpacking the scanner, perform the following steps to remove all the orange
tape and protective materials from it.
1.
Peel off the orange tape from all the places on the outer casing marked
2.
Carefully open the document feed tray and protective sheet.
Document
Feed Tray
3.
Peel off the orange tape from all the places marked
below.
4.
Carefully open the upper unit until it stops (1 1 1 1 1 ), and then remove the protective
sheet (2 2 2 2 2 ).
5.
Check that all the protective tape and protective sheets have been removed, and
then install the roller unit and retard roller in their designated locations.
Roller Unit
Retard Roller
5-1
Follow the steps below to install the roller unit in the upper unit.
1. Flip the lock lever down (1), and slide it to the right (2).
2. Load the roller unit so that its notch aligns with the shaft pin on the scanner.
3. Slide the lock lever to the left (1), and then lift the roller unit into place (2).
4. Flip the lock lever up to lock the roller unit.
5-2
Follow the steps below to install the retard roller on the inside of the roller cover.
1. Remove the roller cover by placing a finger under both ends and pulling upward.
below.
2. Flip up the retard roller lock lever (1), and slide it to the right (2).
3. Load the retard roller so that its notch aligns with the shaft on the scanner.
4. Slide the lock lever to the left so that its shaft fits into the retard roller (1), and then flip
the lock lever completely down to lock the retard roller (2).
5. Attach the roller cover. Make sure the roller cover locks into place by pressing it in the
center with your finger until you hear it click.
6.
Gently close the upper unit. Make sure it is closed securely by pushing on both
edges until you hear a click.
The scanner is now ready for use.
Next, you need to install the scanner software. (
Installing the Software
Install the software before connecting the scanner to the computer.
Warning
Before installing the software, make sure your computer is correctly running one of
the following versions of Windows. For details, refer to the Reference Guide.
• Microsoft Windows 2000 Professional SP4 or later
• Microsoft Windows XP Professional SP3 or later
• Microsoft Windows XP Home Edition SP3 or later
• Microsoft Windows XP Professional x64 Edition SP2 or later
• Microsoft Windows Vista Home basic, Home Premium, Business, Ultimate or
Enterprise SP1 or later
Do not connect the scanner to the computer before installing the software. If you
connect the scanner and turn it ON before you install the software, a wizard screen
will appear. If this wizard appears, click [Cancel] to exit the wizard, and then turn
the scanner OFF.
Wizard Screen (Windows Vista)
Close all other applications before installing the software.
1.
Log on to Windows with Administrator privileges.
2.
Insert the DR-6010C Setup Disc into the
computer's CD-ROM drive.
The setup menu automatically starts up
when you insert the CD-ROM into the CD-
ROM drive. If the setup menu does not start
up, run the setup.exe application on the
CD-ROM.
The setup menu consists of the following screens:
Menu Screen
Read Manuals
* The User Manual and CapturePerfect 3.0
Operation Guide electronic manuals for the
scanner are installed on the computer with
the rest of the software.
3.
Click [Typical Installation].
[Typical Installation] installs the software
(scanner driver, CapturePerfect 3.0) and the
User Manual. The CapturePerfect 3.0
Operation Guide is installed on the
computer during the CapturePerfect 3.0
installation.
4.
Click [Install].
The scanner driver installation wizard
appears. This operation installs both the
scanner driver and the Job Tool.
5.
Click [Next].
6.
Read the software license agreement, and
click [Yes] if you consent to its conditions.
STEP 3)
Installation of the scanner driver starts.
The Job Tool is installed after the scanner
driver.
7.
Click [Finish] to complete the installation.
Next, the installation wizard for
CapturePerfect 3.0 appears.
8.
Click [Next].
Typical Installation
* Installs all of the software displayed.
Custom Installation
* Installs only the selected software.
Continued on back side