Flying Industry Development CWB-4 Короткий посібник - Сторінка 2

Переглянути онлайн або завантажити pdf Короткий посібник для Пульт дистанційного керування Flying Industry Development CWB-4. Flying Industry Development CWB-4 3 сторінки. Rf wireless remote control radio controller / transmitter & receiver

Друкувати сторінку
Setting control mode Latched: Disconnect Jumper-1 and Jumper-2.
Control mode Latched (Channel 1~4): Press -> On, other relays Off; Press other button -> Off.
Such as:
Press button 1: Turn on relay 1 (connect A and B, disconnect A and C)
Turn off other relays (disconnect A and B, connect A and C)
Press button 2: Turn on relay 2 (connect A and B, disconnect A and C)
Turn off other relays (disconnect A and B, connect A and C)
Setting control mode Momentary: Only connect Jumper-1.
Control mode Momentary (Channel 1~4): Press and hold -> On; Release -> Off.
Such as:
Press and hold button 1: Turn on relay 1 (connect A and B, disconnect A and C)
Release button 1: Turn off relay 1 (disconnect A and B, connect A and C)
Press and hold button 2: Turn on relay 2 (connect A and B, disconnect A and C)
Release button 2: Turn off relay 2 (disconnect A and B, connect A and C)
Setting control mode Toggle: Only connect Jumper-2.
Control mode Toggle (Channel 1~4): Press -> On; Press again -> Off.
Such as:
Press button 1: Turn on relay 1 (connect A and B, disconnect A and C)
Press button 1 again: Turn off relay 1 (disconnect A and B, connect A and C)
Press button 2: Turn on relay 2 (connect A and B, disconnect A and C)
Press button 2 again: Turn off relay 2 (disconnect A and B, connect A and C)
Setting control mode Momentary + Toggle: Connect Jumper-1 and Jumper-2.
Control mode Momentary (Channel 1, 2): Press and hold -> On; Release -> Off.
Press and hold button 1: Turn on relay 1 (connect A and B, disconnect A and C)
Release button 1: Turn off relay 1 (disconnect A and B, connect A and C)
Press and hold button 2: Turn on relay 2 (connect A and B, disconnect A and C)
Release button 2: Turn off relay 2 (disconnect A and B, connect A and C)
Control mode Toggle (Channel 3, 4): Press -> On; Press again -> Off.
Press button 3: Turn on relay 3 (connect A and B, disconnect A and C)
Press button 3 again: Turn off relay 3 (disconnect A and B, connect A and C)
Press button 4: Turn on relay 4 (connect A and B, disconnect A and C)
Press button 4 again: Turn off relay 4 (disconnect A and B, connect A and C)
We have learned remote control to the receiver. If you don't want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored
codes have been deleted successfully.
Learning the button of remote control:
1) Press the button of receiver; signal LED on the receiver keeps shining. The receiver enters into status of LEARNING.
2) Press any one button on remote control. If signal LED flashes quickly 15 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, press again the button of receiver, signal LED turns off, learning process will be discontinued.
4) The receiver can learn several remote controls with different codes.
Antenna
C B
Application Circuit
Signal LED
RF module
Relay 1
Relay 2
C
B
A
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Lamp 1
Http://www.carymart.com
Power LED
IC
Relay 3
C B
A
A
Lamp 3
Lamp 2
Relay 4
C
B
A
Lamp 4