AIR GAP ET116-001 Інструкція - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція для Адаптер AIR GAP ET116-001. AIR GAP ET116-001 2 сторінки. Reverse osmosis
Друкувати сторінку1 – Drain Line Adapter with Push-In Connector ET116-001
1 – Hose Coupler
2 – Marine Stainless Steel Hose Clamps
•The ET116-001 provides an IAPMO / UPC listed alternative to the use of the
drain saddle which is a prohibited fitting in the United States.
• To install the ET116-001 reverse osmosis reject water Drain Line Adapter,
follow these instructions.
Please read the instructions once through before starting.
CONFIGURATION – A
1. Disconnect the power supply to the
disposal by unplugging the cord under
the sink, or shutting off the circuit
breaker before starting work.
(Do this for configuration A & B)
2. Remove dishwasher drain hose from
disposal by unscrewing hose clamp, or
expanding spring clamp with pliers. Move
clamp away from disposal nipple, then
twist hose back and forth while pulling away
from disposal to separate. (See Fig. 1)
3. Universal barbs on the
ET116-001 will accommodate the
various dishwasher hoses
encountered. Determine which
size is required by sliding open
end of the hose over stepped
barbs until one fits snugly. If the
hose fits snugly over the middle
or largest barb, you must cut
away the smaller barb(s) with a
hacksaw. Use the grooved "cut
lines" provided, then smooth
away any burrs.(See Fig. 2a)
4. Scrape the inside of the
exposed disposal nipple with a
screwdriver to remove any build
up caused by dishwasher. (See
Fig. 2b)
5. Mount hose coupler (provided)
one inch over disposal nipple.
Then slip both new stainless steel
hose clamps (provided) loosely
over hose coupler. (See Fig. 2c)
ET116-001
Installation Procedures
For Disposal Connection with or without Dishwasher
LIST OF PARTS ENCLOSED
FIG. 1
FIG. 2a
FIG. 2b
FIG. 2c
FIG. 2d
-OVER-
6. Point arrows of ET116-001 toward disposal and slide barbs into
remaining one inch of the hose coupler until firmly seated against the
disposal nipple. Orient the "wye branch" in a vertical position to
receive RO drain tube. Tighten both hose clamps securely over hose
coupler so that the ET116-001 is solidly mounted on disposal.
(See Fig. 2d)
7. Lift the tail of adapter
slightly higher than horizontal,
and position semi-taut
hose behind it. Take a
measurement on the hose
against the selected barb.
(See Fig. 3)
8. Cut off excess hose squarely with sharp knife. Reuse original
spring or hose type clamp by sliding loosely over hose. (See Fig. 3)
9. Twist hose over selected barb, then
slide hose clamp down and tighten
securely.
(See Large Cover Illustration)
Note: Use tautness of dishwasher
hose to keep tail of adapter slightly
above horizontal... this is important
for proper drainage and a clog free
installation. If dishwasher hose
material cannot be easily shortened
or it is undesirable to do so, attach
uncut end of hose to adapter, then tie
up remaining slack with suitable
material.
10. Insert RO drain tube 1/4" into
Push in connector to complete
the installation (See Fig. 4), then
reconnect the power supply to disposal.
Problem: In some instances, the disposal may be oriented away
from the airgap faucet. Solution: redirect the ET116-001 using a ¾"
copper 45° or 90° elbow between the disposal and ET116-001 as
desired (requires an extra hose coupler and two hose clamps).
7/8
3/4
1/2-5/8
(Example only)
Cut hose here
FIG. 3
FIG. 4
Quick Connect / Push-in Connector
Push tube straight past O-ring
to bottom.
FIG. 4a
Tube is secured in position.
FIG. 4b
Push in collet to release tube
FIG. 4c