Astro Pneumatic Tool THOR 401K Посібник
Переглянути онлайн або завантажити pdf Посібник для Заклепочні інструменти Astro Pneumatic Tool THOR 401K. Astro Pneumatic Tool THOR 401K 4 сторінки. Shank thor long barrel air hammer / riveter
Друкувати сторінкуModel:
401K
WARNING
Study, understand and follow all instructions provided
with this product. Read these instructions carefully
before installing, operating, servicing or repairing this
tool. Keep these instructions in a safe accessible place.
INTENDED USE OF THE TOOL
The 401K THOR Air Hammer is designed to work
with .401 shank air hammer bits and attachments
of sufficient professional grade. Do not use this tool
outside of the designed intent. Never modify the
tool for any other purpose or use.
WARNING
Caution: To help prevent personal injury
• Use of this product can expose you to chemicals
such as phthalates which are known to the State of
California to cause cancer, and birth defects or other
reproductive harm. For more information go to
www.P65Warnings.ca.gov/product.
Always wear ANSI approved safety equipment, safety
glasses and clothing when using this product. Study,
understand, and follow all instructions provided with
this product. Failure to read and follow all warnings
and operating instructions may result in damages
and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and By standers).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with
accessories not designed for it could result in
serious injury or death.
• Always select the correct accessories of the correct
size and design for the job that you are attempting to
perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle
is in secure position, and will not move during repair.
BEFORE USE
When unpacking, check the parts diagram and part
number listing on page 4 to make sure all parts are
included. If any parts are missing or damaged,
please call your distributor.
DO NOT DISCARD – GIVE TO USER
Product Type:
0.401" SHANK THOR LONG BARREL
AIR HAMMER/RIVETER
1 YEAR LIMITED WARRANTY
• Astro Pneumatic Tool Co. warrants our products to the
original user against defective material or workmanship
for a period of 1 year (except where noted on our price
schedule) from the date of 1st use. Astro reserves the
right to determine whether the product failed because of
defective material, workmanship or other causes and to
charge back for missing parts. Astro Pneumatic Tool
Co., at its discretion, will repair products covered under
this warranty free of charge. The distributor should
direct the original user to return the product (with the
exceptions listed below) with the distributor's name,
address, adequate proof of date of purchase or a copy
of warranty card, and a short note explaining the
problem. Failures caused by accident, alteration, or
misuse are not covered by this warranty.
• Astro Pneumatic Tool Co. or its authorized service
representatives must perform all warranty repairs. Any
repair to the product by unauthorized service represen-
tatives voids this warranty. The rights under this warran-
ty are limited to the original user and may not be trans-
ferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed
or implied, including warranties of merchantability and
fitness for a particular purpose. Some states do not
allow the exclusion of limitations of incidental or conse-
quential damages so the above limitations may not
apply to you.
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
PRODUCT INFORMATION
• Maximum power .401" shank air hammer for heavy
duty automotive and industrial applications
• Specifically developed THOR model with stroke length
and ported valvebody for power that matches or beats
the top premium options from tool trucks
• Newly designed tilt valve trigger for sensitive power
adjustment at your finger tips
• Features internal brake vibration damping system for
less fatigue No nonsense design: A rotatable forward
grip, sensitive trigger and industry leading power
• Includes quick change chuck, 9.25" length, 10.25"
length, Hi-Flo fittings suggested
Specification:
Air Inlet: 1/4" NPT
Piston Stroke: 3-5/8"
Stroke Speed: 2100 BPM
Net Weight: 5.3 lbs (2.4 kg)
Page 1
www.astrotools.com
Length: 10.25" (260mm)
Hose Size: 3/8"
Air Pressure: 90 PSI
Air Consumption: 11SCFM (1.5CFM)