Canyon 93-705 Інструкція з монтажу - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція з монтажу для Внутрішнє оздоблення приміщень Canyon 93-705. Canyon 93-705 5 сторінок. Charcoal collection student bunk bed
Друкувати сторінку
STUDENT BUNK BED ASSEMBLY INSTRUCTIONS CONFIGURATION TYPE # 1
LIST OF CONTENTS
CHARCOAL COLLECTION
TWIN LOFT BUNK BED END BOX ( 92-706 ) FIG.1
A.- (1) HEADBOARD
3 DRAWER STUDENT LOFT DESK BOX ( 92-710 ) FIG.2 OR
B.- (1) 3 DRW STUDENT LOFT DESK
5 DRAWER STUDENT LOFT CHEST BOX ( 92-711 ) FIG.3
C.- (1) 5 DRW STUDENT LOFT CHEST
TWIN UPPER BUNK BED BOX ( 92-705 ) FIG.4
D.- (1) LOFT BED END
HARDWARE PACK (HPK00095)
E.- (2) METAL DOWEL PINS
6 PCS SIDE RAILS BOX ( 92-730 ) FIG.5
6 PCS SIDE RAILS BOX ( 92-730 ) FIG.5
F.- (4) SIDE RAILS
G.- (2) GUARD RAILS
HARDWARE PACK (HPK00093)
H.- (24) 5/16" X 4" HEX TAP BOLTS
I.- (24) 5/8" CROSS DOWEL NUTS
J.- (24) 5/16" FLAT WASHERS
K.- (1) 5MM ALLEN WRENCH
4 PCS SLAT PACK 3/3 BOX ( 92-645 ) FIG.6
L.- (4) 39" SLATS
HARDWARE PACK (HPK00016)
M.- (8) 1 1/4" SCREWS
FULL BED BOX ( 92-709 ) FIG.7
N.- (1) HEADBOARD
O.- (1) FOOTBOARD
HARDWARE PACK (HPK00094)
P.- (4) CASTER SOCKETS
1.- ASSEMBLE TWIN LOFT BUNK BED, USING ONE HEADBOARD ( A),ONE LOFT BED END ( D),TWO SIDE RAILS ( F),TWO GUARDRAILS ( G), 3 DRW STUDENT DESK (B) OR 5 DRW STUDENT
CHEST(C).
2.- TAKE 3 DRAWER STUDENT DESK (B) OR 5 DRAWER STUDENT CHEST (C), THEN PLACED THEM IN DESIRED POSITION IN THE ROOM,
3.- INSERT ONE METAL DOWEL PIN (E) IN EACH OUTSIDE CORNER OF 3 DRW LOFT DESK OR 5 DRW LOFT CHEST, TAKE THE LOFT BED END, AND PLACE IT ON TOP OF DESK OR CHEST
ALIGNING THE METAL DOWEL PIN WITH EACH PRE - DRILLED HOLE IN EVERY END OF THE LOFT BED END UNTIL THE METAL DOWEL PIN ARE ALL THE WAY IN THE HOLE OF THE BED, SEE FIG.9
4.- INSERT TWO CROSS DOWEL NUTS (I) INTO THE SIDE RAIL AND GUARDRAILS HOLES, MAKE SURE THE GROOVE IS HORIZONTAL, SEE FIG.10
5.- ATTACH TWO SIDE RAILS & TWO GUARD RAILS TO HEADBOARD&LOFT BED END, INSERTING TWO HEX TAP BOLTS (H) TWO WASHERS (J) INTO HEADBOARD&LOFT BED END HOLES,
USE THE 5MM ALLEN WRENCH (K) TO TIGHTEN BOTH HEX TAP BOLTS,
6.- REPEAT THE SAME PROCESS ON ALL FOUR CORNERS.
7.- PLACE FOUR SLATS (L) ON TOP SIDE RAIL CLEATS,ONE SLAT IN BOTH HEADBOARD&LOFT BED ENDS,PUSH THE SLAT AGAINST THE BED END POST (FIG.A) AND TWO SLATS IN THE
MIDDLE AT EQUAL DISTANCE FROM THE END SLATS, THEN EACH SLAT END MUST BE FASTEN WITH ONE 1 1/4" SCREW (M), SEE FIG.12
YES,
HORIZONTAL GROOVE
FIG.10
FIG.9
REV 01 14/04/2016
CANYON FURNITURE COMPANY
(DO NO TIGHTEN COMPLETELY UNTIL ALL PIECES ARE CONNECTED TOGETHER)
NO
FIG.11
PAGE 2 OF 5
A
K.- (1) 3 DRAWER NIGHT STAND
L.- (1) DESK TOP
M.- (1) CASTER BED HEADBOARD
N.- (1) CASTER BED FOOTBOARD
FIG.2
FIG.1
O.- (4) METAL CASTER SOCKET
D
J.- (6) 1 1/4" SCREW
E
FIG.4
L
M
FIG.6
4 PCS SLAT PACK 4/6 BOX ( 92-646 ) FIG.8
Q.- (4) 54" SLATS
HARDWARE PACK (HPK00016)
M.- (8) 1 1/4" SCREWS
FIG. A
B
3 DRAWER NIGHT STAND BOX ( 90-503 )
DESK TOP BOX ( 90-602 )
CASTER TWIN BED BOX ( 90-707,90-709 )
FIG.3
F
H
I
FIG.5
N
O
P
FIG.7
(PLACE FRONT FACE OF DESK OUTWARDS)
FIG.12
KIS01112
C
G
K
J
Q
FIG.8
, SEE FIG.11