Dot-x DNR V SERIES Посібник користувача - Сторінка 5
Переглянути онлайн або завантажити pdf Посібник користувача для Монітор Dot-x DNR V SERIES. Dot-x DNR V SERIES 12 сторінок. 25 inch display
Також для Dot-x DNR V SERIES: Посібник користувача (10 сторінок)
Друкувати сторінку35 RF AGC: (Rf Automatic Gain Control) Range is from 0- 63. 48 is a general
setting. Tune in weakest available channel and adjust for a snow-free picture.
36 HORZ AFC: Range is 0-1. Set to 0. O=AFC2 Normal. 1=AFC2 X 3.
37 WHITE COMPRESS: (White Compression) The range is 0 to 1. Set to 0. 0 =
Enable and 1 = Disable.
38 60HZ SW: (60 Hertz Switched) The range is 0 to 2.
39 PIF VCO: ( PIF Voltage Controlled Oscillator ) . Range is 0-127.
40 RED CUT: B&W tracking adjustment. Range is 0-254. Typical value is 20.
41 GREEN CUT: B&W tracking adjustment. Range is 0-254. Typical value is 0.
42 BLUE CUT: B&W tracking adjustment. Range is 0-254. Typical value is 28.
43 GREEN GAIN: B&W tracking adjustment. Range is 0-254. Typical value is 45.
44 BLUE GAIN: B&W tracking adjustment. Range is 0-254. Typical value is 70.
45 6 KEY SYSTEM: Keyboard type. Set to 1 for 6 key and 0 for 10 key. Range 0-1.
46 A ATT: Audio Attenuation adjustment.
47 A VCO: (Voltage-Controlled Oscillator) range is 0-63. Typical value range 10-39.
48 A FILTER: (Second Audio Program Voltage-Controlled Oscillator) Stereo,
SAP, and dBx filter adjustment. Range is from 0-63.
49 A SPECTRL: Adjustment of stereo separation (3kHz). Range is 0-63.
50 WIDE BAND: Adjustment of stereo separation (300kHz). Range is 0-63.
51 MAX BLK HRS: Determines the maximum block hours that V-chip could be
programmed. Range is 0-99.
52 STRT CH SM: Enable start channel at scan mode. Range is 0-1.
53 RADIO: Enable or disable the access to radio function.
54 AUX: Enables the access to auxiliary input.
55 VCHIP: Enable the V Chip Function.
56 MUTE DISABLE: If it is enabled (set to 1) it disables the functionality of the
Mute Key.
57 EN LA7222: Used in Conceirge Models to enable separate auxiliary inputs
(Camport and Rear Auxiliary)
58 AUTO CAMPORT: Enable Camport sense. When in 1 Camport sense is
20
SAFETY WARNINGS
12. Line-Cord Polarization
This product is equipped with a polarized alternating-current line plug (a
plug having one blade wider than the other). As a safety feature, this
plug will fit into the power outlet only one way. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug still fails to
fit, contact your electrician to replace your obsolete outlet. Do not defeat
the safety purpose of the polarized plug.
Alternate Warnings-This product is equipped with a three-wire ground-
ing-type plug, a plug having a third (grounding) pin. This plug will only fit
into a grounding-type power outlet. This is a safety feature. If you are
unable to insert the plug into the outlet, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of the grounding-
type plug.
13. Power-Cord Protection
Route power supply cords so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention
to cords at plugs, convenience receptacles, and the point where they exit
from the product.
14. Outdoor Antenna Grounding
If an outdoor antenna or cable system is connected to the product, be
sure the antenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges. Article 810
of the National Electrical Code (U.S.A.), ANSI/NFPA 70 provides informa-
tion with regard to proper grounding of the mast and supporting structure,
grounding of the lead-in wire to antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
EXAMPLE OF GROUNDING
ACCORDING TO NATIONAL
ELECTRICAL CODE
INSTRUCTIONS
15. Lightening
For added protection for this product (receiver) during a lightening storm,
or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna or cable system. This will
prevent damage to the product due to lightening and power-line surges.
16. Power Lines
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it
can fall into such power lines or circuits. When installing an outside
5