Dotco 21D Series Посібник з експлуатації - Сторінка 3
Переглянути онлайн або завантажити pdf Посібник з експлуатації для Дриль. Dotco 21D Series. Dotco 21D Series 12 сторінок. .4 hp pistol grip
Друкувати сторінку1. Install ball bearings into both the front and rear plates.
2. Assemble rotor to rear plate/bearing assembly with the rotor's retaining nut. Position and set the rotor as close as
possible to the rear plate, without dragging or rubbing.
a.
A good practice is to stone the blade slots and polish the ends with a medium grit emery cloth.
b.
Assemble components making sure the bearing is firmly seated in the rear plate.
3. Begin tightening rotor nut without over--tightening to
avoid damaging the ball bearing. Alternately spin the
rotor while tightening until clearance is judged to be
proper—about 0.001" clearance.
a.
One method, shown at right, is to use a piece of
pipe which is slightly longer than the rotor, and
tap lightly against work bench several times.
This helps seat threaded components.
b.
A second method is to hold the rotor/rear plate
assembly vertically (plate downward) and strike
the edge of the plate with a wood block.
These parts are suggested as a recommended inventory of spare parts. Where parts are small, low cost, or
easily lost, then we suggest stocking 3 to 4 for every 10 tools. Other larger, lower wear or more expensive
Part
Description
No.
Common Parts For All Models
Ball Bearing --
Sgl Stage & CODE "0"
1005062
Double Stage
1007537
Ball Bearing
1008854
Ball Bearing
1008914
Rotor Blade
1008916
Front Plate
Planet Pin
Single Stage
1008920
Double Stage
Planet Roller
1008924
Single Stage
Double Stage
1008977
Planet Pin -- CODE 4
1009879
Ball Bearing
1012215
Rotor Nut
1017579
Cylinder
1017780
Rear Plate
1110185
Spindle Nut
MOTOR REASSEMBLY
Recommended Spare Parts List for
BUCKEYE Series 21D Drills
parts should be maintained as one (or one set) for every six to ten tools.
Recommended
Spare Parts For
Qty
These Numbers
Per
of Tools
Tool
Tool
1--5
6--10
1
1
2
2
2
4
1
1
2
1
1
2
4
8
20
1
1
2
2
2
4
4
4
8
24
25
50
48
50
100
2
2
4
1
1
2
1
2
4
1
0
1
1
1
2
1
1
2
HARDWOOD
BLOCK
Part
Description
No.
Specific Parts For 21D--100 Series
1006577
Air Screen
1010250
Muffler Felt
1011732
O--Ring
Throttle Valve Assem.
1024712
(complete)
Specific Parts For Throttle Assembly (21D--100 Ser.)
1005045
Spring
1005081
Steel Balls
1008810
Retaining Ring
1021296
Valve Assembly
Specific Parts For 21D--500 Series
1001234
Spring
1008695
O--Ring
1009245
Retaining Ring
1012964
Air Screen
1019558
Muffler Felt
Page 3
PL32--21D
September 14, 2001
0.001"
CLEARANCE
ROTOR
PIPE OR
SPACER
FLAT SURFACE
Figure 3
Recommended
Spare Parts For
Qty
These Numbers
Per
of Tools
Tool
Tool
1--5
6--10
1
2--3
3--4
1
1
1
2--3
3--4
1
1
1
1
2
4
1
2--3
3--4
1
1
1
1
1
2--3
3--4
1
2--3
3--4
1
2--3
3--4
1
1
2
2
2
8
2
2
2