Amphenol PL183 300 Series Посібник з монтажу - Сторінка 4
Переглянути онлайн або завантажити pdf Посібник з монтажу для Кабелі та роз'єми Amphenol PL183 300 Series. Amphenol PL183 300 Series 9 сторінок. 3pos powerlok g2 180d plug connector
Друкувати сторінку
步骤3：压接铜环
Step 3: Crimping Copper ring
3-1 将 ⑨内铜环从右端移动到屏蔽线下方，屏蔽线覆盖在铜环表面
3-1 Move the ⑨ inside copper ring from the right side to the side below the shield. The shield line is covered on
the surface of the copper ring
确保此处铜环前端和外被前端贴紧，
压紧后间隙最佳为0mm
Be sure to be closely in here, the best
clearance is 0mm after crimping
3-2 取1pcs ⑧外铜环，铜环从左端安装到屏蔽线上，铜环从屏蔽线的左端开始完全覆盖,并压接在其上(规格参照
表3)
3-2 Take 1pcs ⑧ Outer Copper ring, load it to the cable end on the left, copper ring cover the shielded fully from
the shielded left end, then crimp(refer to table 3)
⑧ Outer Copper Ring
外铜环
紧靠外被口 Close to the outer Jacket
Table 3： Copper Ring and Cable braids Crimping spec & retention force requirement
连接器
Connector
301/300系列
301/300 Series
压接工具：油压机
Crimping tool : Hydraulic press
50mm²压模：195195150D50
50mm²Die： 195195150D50
70mm²Die:
220220150D70
70mm²压模： 220220150D70
⑴
建议使用安费诺H+S线材（H+S线材型号详见步骤1-1），如果客户选用其它电缆，请联系安费诺业务，协商订制零配件
Recommend to use H+S cable.(See section 1-1 for details of H+S cable part numbers.) If you need to use customized cable, Please contact
local sales for product extentions
⑵
压接高度和拉拔力需要配合压接截面的金相分析，客户才能判断压接质量合格
Customers need to reconfirm cross section on crimping area and pull out force test to confirm the quality of crimp process
Rev.05 20211123 Document No: 8P1092
三芯2代直头组装式连接器安装说明The Assembly
表3：铜环与线缆屏蔽编织层压接规格&拉拔力要求
线缆尺寸
线缆外径
Cable size
Accepted cable OD (mm)
50mm²
70mm²
Manual
外铜环紧靠外被口
Outer Copper Ring Close to the outer Jacket
(1)
Crimping height (mm)
14.9±0.3
17.0±0.3
for 3POS PowerLok G2 180D Plug Connector
⑨ Inside Copper Ring
内铜环
5+/-1
压接之前，确保
此处外铜环后端
和内铜环后端平
齐
Make sure the
ends are level
with each other
before crimping
压接高度(2)
18.0±0.25
20.3±0.25
参考抗拉拔力
(2)
Retention Force
150N
150N
03-07