CARBONE TG109136-8 Посібник - Сторінка 4
Переглянути онлайн або завантажити pdf Посібник для Дриль. CARBONE TG109136-8. CARBONE TG109136-8 9 сторінок.
Друкувати сторінку
Components, Specifications and Accessories
2
3
1
10
Components list
1 Depth gauge
2 Chuck
3 Locking screw for depth gauge
4 Drill/Impact action selector switch
5 Switch lock button
Technical Specifications
Model No.:
TG109136
Rated power input:
850W
Rated voltage:
220-240V~50/60Hz
No-load speed:
0-2 00/min
Impact rate:
0-
/min
Chuck capacity:
1.5-13mm
Model No.:
TG109136-6(ISRAEL plug)
Rated power input:
850W
Rated voltage:
220-240V~50/60Hz
No-load speed:
0-2 00/min
Impact rate:
0-
/min
Chuck capacity:
1.5-13mm
Double insulation :
Accessories :
1. Auxiliary handle 1pcs 2. Depth gauge 1pcs 3. Chuck key 1pcs 4. Carbon brushes 1set
4
5
9
8
7
6
6 Cable sleeve
7 On/Off switch
8 Variable speed control
9 Forward/reverse selector switch
10 Auxiliary handle
UTG109136
TG109136-8(BS plug)
TG109136S(SAA plug)
850W
850W
850W
110-120V~60Hz
220-240V~50/60Hz
220-240V~50/60Hz
0-2400/min
0-2 00/min
0-2 00/min
0-384 /min
0-
/min
0-
1/16˝-1/2˝
1.5-13mm
1.5-13mm
TG109136E
TG109136-4(IRAM plug)
850W
850W
220-240V~50/60Hz
220-240V~50/60Hz
0-2 00/min
0-2 00/min
0-
/min
0-
1.5-13mm
1.5-13mm
4
Operation
Warning: Before using your drill be sure to read the instruction
manual carefully.
Installing the auxiliary handle (see Dia1)
For your personal safety we recommend using the
auxiliary handle at all times.
To fit the handle, loosen the locking screw for
handle collar anti-clockwise. Slide clamping loop
over the handle collar. Rotate the handle around
the handle collar until the handle is in the desired
position. Tighten the locking screw clockwise to
secure the handle. If you are right handed fit the
handle as shown in Dia2. If you are left handed fit
the handle the other way round.
Installing the depth gauge (see Dia2)
The depth gauge can be used to set a constant
depth to drill. To use the depth gauge, loosen the
locking screw for gauge by rotating the auxiliary
handle anti-clockwise. Insert the depth gauge
through hole in handle. Slide the depth
gauge to required depth and tighten the locking
screw by rotating the locking screw clockwise.
Inserting a tool into chuck (see Dia3)
Warning: Before installing tool,
remove mains plug from mains supply.
Remove chuck key from key storage tab at base
of drill handle, place key into chuck, turn key
anti-clockwise to undo/loosen chuck, inset
drill/tool and firmly tighten chuck by turning
key clockwise. Remove key and replace in storage
tab at base of drill handle.
Operating the On/Off switch (see Dia4)
Press the on/off switch in for operation, release
switch to stop.If you wish to use the drill
/min
continuously the switch lock button can be
pushed in after the on/off switch has been
depressed. To release the lock button simply
depress on/off switch fully, the button will
automatically release.
Variable speed control selector (see Dia5)
/min
The maximum speed can be altered by turning
the variable speed control. Turn clockwise to
increase and anti-clockwise to decrease speed.
The speed of the drill varies with the amount of
pressure applied to the on/off switch, i.e. more
pressure for higher speed.
Dia 1
Dia 2
Dia 3
Dia 4
Dia 5
5