Comelit 20005000 Технічний посібник - Сторінка 5

Переглянути онлайн або завантажити pdf Технічний посібник для Обладнання для запису Comelit 20005000. Comelit 20005000 13 сторінок. Vip interface for simplebus2 systems

Друкувати сторінку

Art. 20005000 allows monitors and home automation system managers for the ViP system to

be used in Simplebus2 audio/video setups. The ViP monitors/system managers can be used to

receive calls from the external unit and send commands to Simplebus2 devices (self-ignition, call

to main/secondary switchboard, intercom call, actuator control, camera module control, etc.); the

device also offers integration with the SimpleHome home automation system and video entry

phone call forwarding via the Comelit App.

Equipped with 1 Comelit PoE Ethernet port for connection to the ViP monitor and terminals for

connection to the Simplebus2 system.

In relation to the SImplebus2 section of the system, the device should be considered as a separately

powered Simplebus monitor.

Power LED

Connection terminals

| L | L | Simplebus2 Data line

| + | - | Power supply Positive / Negative 12/56 VDC

CV5 Jumper for video closure (Factory setting: closed)

Jumper closed if there is no Simplebus monitor on the line

Jumper open if there are successive Simplebus monitors connected in cascade on the line

DIP-Switches Selectors used to set the Simplebus address

DIP-Switches Selectors used to implement reset procedures (See "Reset procedures")

Indicator LED

Flashing slowly

Steadily lit

System starting up

Simplebus line present

/ updating

System ready

CV1 (Factory setting: closed)

Jumper open if at least one Simplebus monitor with the same address is on the line

LAN port - Comelit PoE Output - IP address Factory setting: DHCP

Only connect to the router or PC using red Comelit cable 1449

Indicator LED

Red

Green

Steadily lit

Normal operation

Steadily lit

Flashing

See "Reset procedures"

Flashing

Technical specifications

Power supply voltage

12 ÷ 56 VDC

Max. absorption (mA)

1100 ÷ 450 (in relation to the power supply voltage)

200 mA 12 V

Max. current delivery

300 mA 24 V

Operating temperature

-5 ÷ 50°C

Operating humidity

5 ÷ 95%

Dimensions

90 x 70 x 59 mm (4 DIN modules)

Functions

Art. 20005000 allows use of the Comelit video entry system functions, with the exception of: Call

divert / Range / Selective intercom / Alarm.

CFP (Floor door call): If there are both Simplebus monitors and ViP monitors in the apartment,

connect the CFP to just one Simplebus monitor to receive the call on all monitors.

Fig. 1

Flashing quickly

Simplebus line missing

/ short-circuited

Yellow

Normal operation

Ethernet connection

present

See "Reset procedures"

400 mA 48 V

400 mA 56 V

ViP monitor addressing

The address of a monitor in a Simplebus system is the address of the apartment preceded by

SBVIP

Examples

Apartment 1

Apartment 2

If the ViP monitor keypad does not allow the entry of alphanumeric codes, proceed using ViP

Manager software.

Addressing Simplebus devices

To allow the ViP monitor to communicate with Simplebus devices connected to the system,

addresses must be assigned, in the ViP monitor directories, in accordance with the table:

External unit

SBEXT001

(Function: Self-ignition)

Secondary switchboard

(Function: call to secondary

SBCPS007

switchboard)

Main switchboard

SBCPS008

(Function: call to main switchboard)

Caretaker door-entry phone

(Function: call to caretaker door-entry

SBCPS009

phone)

Internal unit

SBINTxxx

(Function: general intercom call)

Reset procedures

Reboot with predetermined network

settings

This procedure allows you restart the device

with the default network parameter settings,

while keeping the other settings unchanged.

√ DIP-switches in the default positions (OFF)

1. Switch off the power supply to the device

2. Set DIP1 to ON

3. Power on the device

4. Wait 20-40 sec. until the LEDs start flashing

slowly and alternately (1 sec. red / 1 sec.

green)

5. Return the DIP-Switche to OFF

›› The green LED will flash for 5 sec..

›› The device will start with the default network

settings.

6. At the next restart, the device will recover

the saved settings.

Simplebus address

ViP address

001

SBVIP001

029

SBVIP029

Generic actuator

SBACT255

(Function: generic actuator control)

Coded actuator xxx

SBACTxxx

(Function: coded actuator control)

Generic camera module

(Function: generic call module

SBCAM255

control)

Addressed camera module xxx

(Function: addressed camera

SBCAMxxx

module control)

Restoring factory settings

This procedure allows you to restore all the

factory parameter settings and to delete all

the device configurations.

√ DIP-switches in the default positions (OFF)

1. Switch off the power supply to the device

2. Set all the DIP-switches to ON

3. Power on the device

4. Wait 20-40 sec. until the LEDs start

flashing rapidly and alternately (0.1 sec.

red / 0.1 sec. green)

5. Return all the DIP-Switches to OFF

›› The red LED will flash for 5 sec.

›› The device will reset all parameters to the

factory settings and restart in the normal

way.