Amsberg A10G Посібник користувача

Переглянути онлайн або завантажити pdf Посібник користувача для Підсилювач Amsberg A10G. Amsberg A10G 2 сторінки. Gsm/cdma single band consumer booster

Друкувати сторінку

Preface

This user's manual describes the installation, commissioning and maintenance of

GSM/CDMA wide band consumer boosters of single band.

Please do read user manual carefully before installing and maintaining the

booster.

The information in this manual is subject to change without prior notice.

Opinions are welcomed about the manual improvement.

Safety Warnings

：

Users must follow the below principles

Booster should follow system requirement of communication equipment,

assure good grounding and lightning protection.

The power supply voltage of booster should meet the standards of security

requirement; any operation shall be carried out only after cutting off power in

advance. Only the professional is authorized for the operation.

Do not dismantle machine, maintain or displace accessories by yourself,

because in this way, the equipment may be damaged and you may even get

an electric shock.

Do not open the booster, touch the module of booster, or open the cover of

module to touch the electronic component. The components will be damaged

due to electrostatic.

Please keep away from heating-equipment, because the booster will

dissipate heat during working. And do not cover booster with anything that

influences heat-dissipation.

Overview

CDMA or GSM single band consumer booster is designed to help mobile users

amplify weak signals of 2G, 3G. They are bi-directional amplifiers.

The donor antenna receives the signals from the cell tower, and transmits to the

signal booster, the signal booster amplifies them and then the indoor antenna will

retransmit to your mobile device.

Vice Versa, the signals produced by your phone are also received by indoor

antenna, amplified by the booster and then send back to cell tower by donor

antenna.

DC IN

Indoor Port

LNA

RF SAW

Drive

AC IN

ATT ALC

( To server ant )

POWER SUPPLY

Duplexer

Attenuator

Outdoor Port

ATT

LED Monitor

Drive

RF SAW

LNA

( From Donor ant )

Package contents

Booster

Adapter

Wide Band Yagi Antenna Panel Antenna Whip Antenna

(Standard configuration)

(Optional accessories)

Main specification

• GSM/CDMA specification

RF Parameter

GSM

890~915MHz

Frequency Range

CDMA

824~849MHz

Band width

GSM/CDMA

25MHz/25MHz

F17

65dB

Max.Gain

F23

65dB

F17

17dBm

Max. output power

F23

17dBm

MGC (Step Attenuation )

≥31dB/1dB step

Automatic Gain Control

≥31dB

Frequency stability

≤0.01ppm

Electrical Parameter

Power Supply

Input AC100~240V.50/60Hz, Output DC5V/3A

Power Consumption

≤4W

Input & Output Impedance

50 ohm

Indicator

1)Green: Power ON

POWER LED

2)OFF: Power OFF

1)Green:No loop back or no self-oscillation

2)Slow Flashing Green: Slight loop back or self-oscillation

ISO LED

3)Quick Flashing Green: Deep loop back or self-oscillation

4)Quick Flashing Red: Severe loop back or self-oscillation

1)Green: Output power is not full

2)Slow Flashing Green: Full output power

ALARM LED

3)Quick Flashing Green: Output power is over rated

4)Quick Flashing Red: Output power is severe over rated

Mechanical Parameter

I /O Port

N-Female

Dimensions

120*135*34mm

Weight

≤0.5Kg

Environment Parameter

Operating Temperature

0ºC~+55ºC

Storage Temperature

-10ºC~+80ºC

Humidity

5% - 95%

Atmospheric pressure

55 kPa -106 kPa

Environment Conditions

IP40

Installing your hardware

Before you install

•

Make sure you have sufficient cable length between proposed donor/server

antenna location and booster connector.

• Make sure the position you install the booster is near to one existing electrical

outlet, and well ventilated, away from excessive heat, moisture, and direct

sunlight.

Installation tools and accessories:

Num.

Name

Plastic expansion bolt

Tapping screw

Hanging folder

Reciprocating drill

935~960MHz

Shot bit

869~894MHz

Installation overview

70dB

• Install your donor antenna on the roof where there is the strongest signal.

17dBm

• Mount your signal booster, connect the cables to the signal booster from the

23dBm

outdoor antenna and indoor antenna at the designated ports, and connect the

booster to the AC supply(make sure all the cables are connected).

• Install the indoor antenna where you want to improve the signal.

Find the area with the strongest signal

The booster's main function is to improve weak RF signals of an area. The signal

strength from the outdoor antenna directly affects the efficiency of indoor

coverage.

User's Manual

Specification

Quantity

Remark

Standard accessories

Ø6

Standard accessories

M4*25

Standard accessories

Engineering-owned

Ø6

1.Wide Band Yagi Antenna

2.Booster

3.Indoor Panel Antenna

Single Band Consumer Booster

GSM/CDMA