Dr. Neuhaus Sagemcom ZDUE-450-PLUS-VII Інструкція з монтажу

Переглянути онлайн або завантажити pdf Інструкція з монтажу для Вимірювальні прилади Dr. Neuhaus Sagemcom ZDUE-450-PLUS-VII. Dr. Neuhaus Sagemcom ZDUE-450-PLUS-VII 2 сторінки.

Друкувати сторінку

ZDUE-450-PLUS-VII Installation Instructions

Safety Notes

Incorrect installation, commissioning or operation

can lead to serious damage to property and

personal injury and to death.

Please read these instructions carefully before installing,

commissioning and using the ZDUE-450-PLUS-VII. Use the

appliance only as described in the data sheet and the

manual.

The

ZDUE-450-PLUS-VII

meets the requirements of safety

standard

EN 62368-1

(protection class 2).

Qualified personnel:

Installation and commissioning of the ZDUE-450-PLUS-VII

and the accessories may only be carried out by electricians.

They must be trained and qualified

hazards and to install, commission, ground and mark

appliances, systems and circuits in accordance with the

standards and recognized rules of technology.

Connection to the house installation:

An easily accessible, all-pole circuit breaker in the power

supply circuit is required for the house installation.

Alternatively, a single-pole circuit breaker can be used in the

outer conductor as long as a distinct neutral conductor has

been integrated into the supply line. Observe country-

specific regulations. In Germany, the circuit breaker must at

least meet the requirements of the DIN VDE series 0100

standards (see CENELEC HD384; IEC 60364).

For the house installation, there must be an installation fuse

that complies with the DIN VDE series 0100 standards (see

CENELEC HD384; IEC 60364) and is properly adapted to

the cable cross-section of the power supply line. The

additional short-circuit protection must have a selectivity of I

> 1500A.

The appliance is not suitable for connection to an electrical

supply network with IT configuration (IT system).

Cable Routing:

The space between antenna/data lines and lines carrying

dangerous voltages must be at least 10 mm.

Location:

Never use the

ZDUE-450-PLUS-VII

operation of radio equipment is prohibited. The appliance

contains a radio transmitter, which can possibly impair the

function of medical electrical appliances such as hearing

aids or cardiac pacemakers.

The

ZDUE-450-PLUS-VII

is suitable for use in overvoltage

category III.

If the appliance is likely to be exposed to higher

transient over voltages than those in

when connected, it will be necessary to take further safety

precautions for the installation.

Antenna Installation

Indoor and outdoor antennas of the appliance may be

installed and operated only with a minimum distance of 20

cm from humans.

The antennas must be installed and operated so that they

do not interfere with other antennas or devices.

When using a directional antenna, observe the legal limit for

electromagnetic fields (0 Hz to 300 GHz) in public areas.

For details, see Council Recommendations 1999/519/EC of

12 July 1999.

It is mandatory, that the installation of an outdoor antenna

must be carried out by a qualified electrician. The standards

EN 60728-11 and VDE 0855-300 as well as any other

national installation guidelines for lightning protection must

be followed.

to detect and avoid

in areas where the

overvoltage category

III

Intended Use

The ZDUE-450-PLUS-VII is an appliance designed for the

remote inquiry and the remote monitoring of electricity, heat,

gas and water meters. It is design to be used in mobile radio

networks.

Opening the device

In order to insert the SIM card or to access the DIP switch,

you first have to open the device:

First disconnect all the poles of the device from the

electricity supply if it is plugged in there.

Now unscrew the screw in the terminal cover and

remove the cover.

Now remove the device lid.

Altering the device settings

Using the DIP switch (4) you toggle between

the both operating modes, meter mode and

AT command mode.

In meter mode (OFF), the device can be

adjusted locally via one of the meter

interfaces or remotely via communication

commands according to EN 62056-21. In this

case, the device will then operate using the

parameters that have been set.

Setting the PIN of the SIM card

In order to operate the ZDUE-450-PLUS-VII, you will require

a plug-in SIM card (1,8V only) from a mobile radio network

operator.

A ZDUE-450-PLUS-VII having factory default settings

expects a SIM card with a PIN 0000. The PIN setting of the

ZDUE-450-PLUS-VII can be changed in the device settings.

Inserting the SIM card

Insert the SIM card as follows:

Open the SIM card holder by gently pressing the lid

towards the edge of the device, flip it up and insert the

SIM card into the slot in the holder. The gold-plated

contacts on the SIM card have to lie on the gold-plated

contacts of the holder when the holder is closed.

Close the lid of the SIM card holder and lock it by

pressing it gently back towards the center of the device.

You will feel it click into place.

Now replace the device lid and the terminal cover.

Mobile Radio Net Status

/ Error LED

Status LEDs

Service connector

(optional)

DIP switch

SIM card holder

SMA antenna connector

(SMA or FAKRA-D)

Service push button

Terminal block (RS485)

RS232 interface

Terminal block

Current Loop LED