Electrolux BRT217TGW0 Посібник з використання та догляду - Сторінка 7
Переглянути онлайн або завантажити pdf Посібник з використання та догляду для Холодильник Electrolux BRT217TGW0. Electrolux BRT217TGW0 18 сторінок. Top mount refrigerator
Друкувати сторінку
TOREMOVE F REEZER H ANDLE:
(Handles may beeasier toreverse while doors a reofh)
1. Remove twoscrews a ttaching handle t obottom offreezer
door.
2. Remove short t rimpiece bysliding trim straight upandoff
ofhandle b racket.
3. Remove screw attaching topofhandle t odoor.
4. Magnetic N ameplate Mode_s: Gently p rymagnetic
nameplate frame from door. R emove nameplate from its
frame, turnframe upside down andinstall _ n oldnandle
holes. Insert magnetic namepIate intofram_
Se_f-Adhesive
Nameplate Models:
Gently p eel o ff
nameplate fromdoor
Frame_
and reapply over old
handle holes.
Trim --,
TO ATTACH
FREEZER
HANDLE:
1.
ReinstalI handle on
opposite side, using
same hole as
nameplate.
2.
Attach handle to
bottom of door.
Serf Adhesive
3.
Slide trim piece
Nameohte
straight down onto
-
(somemodels)
handle bracket.
TO REMOVE FREEZER HANDLE:
(Handles may be easier to reverse while doors are off.)
1.
Remove two screws attaching handle to bottom of freezer
door.
2.
Remove button plug using edge of putty knife.
3.
Remove screw on side of freezer door and remove
handle,
TO ATTACH
FREEZER
--'Screw
HANDLE:
1,
Secure side of
.........................
handle to door and
"
replace button plug.
2.
Secure handle to
bottom of door.
(Handles may be easier to reverse while doors are off.)
1.
Remove two screws attaching handle to bottom of freezer
door.
2.
Swing bottom of handle away from the door and slide
handle straight up and off of dovetail button.
3.
Remove screw and dovetail button and install on other
side, using the same holes as nameplate.
4.
Magnetic
Nameplate
Models: Use putty knife to gently pry
magnetic namepIate frame from door. Remove namepIate
from its frame, turn frame upside down and instalI in oId
handle holes. Insert magnetic nameplate into frame.
Serf-Adhesive
Nameplate
Models:
Use putty knife to
gently peel off nameplate from door and reapply over old
handle holes.
TO ATTACH
FREEZER
HANDLE:
1,
Start with handle
(somemodels
offset away from
doon Place top of
handle over dovetail
button, swing handle
into an upright
position and pull
downward, locking it
into piace.
2.
Secure bottom of
handle with two
LockHandle
over
screws removed
Screw-.LL,_
Doveta!! B _tton
earlier.
TRIM REMOVAL
(FULL-LENGTHTRIM
MODELS
ONLY)
In some models, the refrigerator door has a full length trim
piece which continues from the bottom of the handle to the
bottom of the door, The top of the trim attaches to the handle
bracket (Figure 1) or fits around the base of the handle (Figure
2), An adhesive "trim lock" is positioned about halfway down,
The bottom of the trim is held in place by either an adhesive
trim lock, or a trim lock with two prongs inserted into a hole on
the face of the doon
TO REMOVETRIM:
1,
Remove trim by gently pulling trim lock areas out and
away from door,
2,
When trim is free from door, slide the trim straight down
_"
_
and away from base of handle.
Handle
,,r"
Scre_