Bosch DISHWASHER Інструкція з експлуатації Посібник з експлуатації - Сторінка 18

Друкувати сторінку

Bosch DISHWASHER Інструкція з експлуатації Посібник з експлуатації

Self Help

Dishwashers may occasionally exhibit problems that are unrelated to a malfunction of the dishwasher

itself. The following information may help you with a dishwasher problem without involving a repair

professional.

Problem

1. Door may not be properly latched

2. Unit may not be turned on

3. Unit not reset or previous cycle not completed

4. Delay start engaged

Dishwasher

5. Interruption of electrical power supply to dishwasher

does not start

or blown fuse.

6. The door may have been closed without first selecting

a cycle

7. Water supply may not be turned on

Dishwasher

1. Default factory settings alert the customer that the

beeping (end of

cycle is complete by beeping. This feature can be deacti-

cycle signal)

vated if so desired.

Display does not

1. A fuse may have been blown or circuit breaker tripped

illuminate or

2. Door not closed or latched

console lights

Note: For models with controls on top of the door, the dis-

are not on

play only illuminate when the door is opened and con-

trols are visible.

Dishwasher

1. Incoming water is not warm enough

seems to run a

2. Cycle time can vary due to soil and water conditions

long time

3. Rinse agent dispenser is empty

4. Dishwasher connected to cold water supply

Note: Refer to "wash cycle information" section in this

manual for typical cycle lengths

Dishes are not

1. Spray arm movement obstructed

getting clean

2. Spray arm nozzles clogged

enough

3. Improper use of detergents

4. Filters could be clogged

5. Dishes are nested or loaded too close together

6. Selected wash cycle is not suitable for food soil condi-

tions

Dishes are not

1. Rinse agent dispenser is empty

getting dry

2. Improper loading of dishes

enough

3. Selected cycle does not include drying

Note: Plastic or Teflon do not typically dry as well as other

items due to their inherent properties

Cause

Action

1. Shut the door completely

2. Press the main power switch to turn unit on

3. To reset, refer to "cancelling or changing cycle" in this

manual

4. To reset, refer to "delay start" section in this manual

5. Check circuit breaker

6. Select a cycle and close the door.

7. Check and turn on water supply

1. To adjust the volume or deactivate, refer to the "cycle

completion signal" section in this manual.

1. Check the fuse or circuit breaker box and replace the

fuse or reset the breaker if necessary

2. Ensure door is properly latched and completely closed

1. Before starting a cycle, run hot water faucet at the sink

closest to the dishwasher

2. Sensors in the dishwasher automatically increase the

cycle time to ensure a good wash when heavy soil is

detected

3. Add rinse agent

4. Verify dishwasher is connected to hot water supply

plumbing

1. Ensure that spray arm movement is not blocked by hand

rotating spray arms before starting cycle

2. Remove the spray arms and clean according to the "care

and maintenance" section of the manual

3. Increase or decrease detergent depending on the water

hardness (refer to Table 1)

4. Clean the filters according to the "care and maintenance"

section of the manual

5. Rearrange load such that water spray can reach all items

in the dishwasher - see "loading the dishwasher" section of

the manual

6. Refer to "wash cycle information" section of the manual

1. Add rinse agent - the use of rinse agent improves drying

2. Rearrange load to ensure items are not nesting (see

"loading the dishwasher" section of the manual)

3. Rinse and Hold setting does not include drying

Note: Santitize option and Intensive Drying feature also

improve drying performance.