AirStage AJH045LBLAH Посібник з монтажу - Сторінка 3

Переглянути онлайн або завантажити pdf Посібник з монтажу для Кондиціонер AirStage AJH045LBLAH. AirStage AJH045LBLAH 19 сторінок. Outdoor unit

Друкувати сторінку

This mark indicates procedures which, if improperly per-

CAUTION

formed, might possibly result in personal harm to the user, or

damage to property.

This unit must be installed by qualiﬁ ed personnel with a capacity certiﬁ cate for handling

refrigerant ﬂ uids. Refer to regulation and laws in use on installation place.

The installation must be carried out in compliance with regulations in force in the place

of installation and the installation instructions of the manufacturer.

This unit is part of a set constituting an air conditioner. It must not be installed alone or

with non-authorized by the manufacturer.

This unit contains no user-serviceable parts. Always consult authorized service person-

nel to repairs.

When moving, consult authorized service personnel for disconnection and installation of

the unit.

• Obtain the distribution network operator's agreement about the power capacity of the

power supply system, speciﬁ cation of the cable and the harmonic current, and etc.

when you connect the outdoor unit with the power supply.

• This unit must be connected to a power supply with impedance of 0.398 ohm and

below. If the power supply does not satisfy this requirement, please consult the power

supplier.

• This product is intended for professional use.

Be sure to use a dedicated power circuit.

Never use a power supply shared by another appliance.

Do not install the unit in the following areas:

• Area with high salt content, such as at the seaside.

It will deteriorate metal parts, causing the parts to fall or the unit to leak water.

• Area ﬁ lled with mineral oil or containing a large amount of splashed oil or steam, such

as a kitchen.

It will deteriorate plastic parts, causing the parts to fall or the unit to leak water.

• Area that generates substances that adversely affect the equipment, such as sulfuric

gas, chlorine gas, acid, or alkali.

It will cause the copper pipes and brazed joints to corrode, which can cause refriger-

ant leakage.

• Area containing equipment that generates electromagnetic interference.

It will cause the control system to malfunction, preventing the unit from operating

normally.

• Area that can cause combustible gas to leak, contains suspended carbon ﬁ bers or

ﬂ ammable dust, or volatile inﬂ ammables such as paint thinner or gasoline.

If gas leaks and settles around the unit, it can cause a ﬁ re.

• Avoid installing the unit at places where it will come into contact with animals' urine or

ammonia.

The units are not explosion proof and therefore should not be installed in explosive

atmosphere.

Do not use the unit for special purposes, such as storing food, raising animals, growing

plants, or preserving precision devices or art objects. It can degrade the quality of the

preserved or stored objects.

Ground the unit. Do not connect the ground cable to a gas pipe, water pipe, lightning

rod, or a telephone ground cable. Improper grounding may cause electric shock.

Perform draining for the unit according to the Installation manual. Check that the water

is properly drained.

If the drain processing is improperly installed, water may drip down from the unit, wet-

ting the furniture.

Do not touch the ﬁ ns with bare hands.

Be sure not to start or stop the operation of air conditioning with power breaker. Other-

wise, it may cause malfunction or water leakage.

When setting it up near the equipment that generates electromagnetic waves and the

equipment that generates the higher harmonics wave, be sure to take measures against

noise. Otherwise, it may cause malfunction or failure.

When energizing to the crankcase heater, please turn on the power 12 hours or earlier

before operation begins. When the energizing time is short, it may cause failure. Be-

sides, please do not turn off power during the busy season.

Children should be monitored to ensure they do not play with the device.

This product is not intended to be used by people (including children) with physical, sen-

sory or mental disability, or persons lacking experience or knowledge unless they have

been given by the through a person responsible for their safety, supervision or instruc-

tion concerning the use of the device.

2. ABOUT THIS PRODUCT

2.1. Precautions for using R410A refrigerant

Pay careful attention to the following points:

Since the working pressure is 1.6 times higher than that of R22 models, some of the

piping and installation and service tools are special. (See the table in the SPECIAL

TOOLS FOR R410A section.)

Especially, when replacing a conventional refrigerant (other than R410A) model with

a new refrigerant R410A model, always replace the conventional piping and ﬂ are nuts

with the R410A piping and ﬂ are nuts.

Models that use refrigerant R410A have a different charging port thread diameter to pre-

vent erroneous charging with R22, R407C and for safety. Therefore, check beforehand.

[The charging port thread diameter for R410A is 1/2 UNF 20 threads per inch.]

Be more careful than the installation of the refrigerant (other than R410A) models, not

to enter foreign matters (oil, water, etc.) and other refrigerant into the piping. Also, when

storing the piping, securely seal the openings by pinching, taping, etc.

When charging the refrigerant, take into account the slight change in the composition of

the gas and liquid phases, and always charge from the liquid phase side whose compo-

sition is stable.

2.2. Special tools for R410A

Tool name

Pressure is huge and cannot be measured with a conven-

tional gauge. To prevent erroneous mixing of other refriger-

ants, the diameter of each port has been changed.

Gauge manifold

It is recommended to use a gauge manifold with a high

pressure display range -0.1 to 5.3 MPa and a low pressure

display range -0.1 to 3.8 MPa.

To increase pressure resistance, the hose material and base

Charging hose

size were changed.

A conventional vacuum pump can be used by installing a

vacuum pump adapter.

• A conventional vacuum pump can be used by installing a

Vacuum pump

vacuum pump adapter.

• Be sure that the pump oil does not back ﬂ ow into the sys-

tem. Use one capable for vacuum suction of -100.7kPa (5

Ton, -755mmHg).

Gas leakage detector

Special gas leakage detector for HFC refrigerant R410A.

2.3. Accessories

Use connecting parts as required.

Do not throw away the connecting parts until the installation has been complete.

Name and shape

Speciﬁ cations

manual

Installation

manual

Drain cap

Drain pipe

Cable tie

Reducer

One-touch bush

Contents of change for R22 tool

Q'ty

Application

—

(This book)

For outdoor unit drain piping work

For binding power cable and trans-

mission cable

For connecting gas pipe

(For 54 model)

For power supply cable and

connection cable installation

En-2