Dragonfly DF-SL-133-MW/HC Інструкція з монтажу

Переглянути онлайн або завантажити pdf Інструкція з монтажу для Проекційний екран Dragonfly DF-SL-133-MW/HC. Dragonfly DF-SL-133-MW/HC 2 сторінки. Fixed film screen with black velvet frame

Друкувати сторінку
Mounting the screen onto the wall
• Select an appropriate area to mount the screen. Make sure the
position selected will not interfere with existing features of
your room; wall sockets, switches, etc... these all should be
avoided.
• DO NOT install the screen over an electrical outlet or switch.
Doing so poses a serious fire hazard.
• For homes with stud-wall construction, use stud finder or
carefully measure to determine where the studs are located in
the wall. The screen MUST be mounted to the studs- NEVER
rely on gypsum board, drywall, or thin wall materials to
support the weight of the screen!
• The screen is equipped with a set of pre-measured tethered
mounting brackets. There are security clips in the bottom
bracket. The screen should sit centered on the mounting
bracket when installed.
Top Bracket
Pre-measured
Tether
Bottom Bracket
Security Clip
• Drywall/Stud Installation: Using a stud finder, locate studs in
wall. Hang top bracket first (subtracting 1/2" from top of
screen to mark corner edge of top of bracket) with 5X40mm
Philips head screws and washers directly into studs. Pre-
drilling studs with a 5/32" drill bit is recommended.
• Let the bottom bracket drop and, while pulling tethers taut ,
mark locations for screws. Repeat mounting procedure
used with the top bracket. For best support, 3 screws per
bracket should be used.
• Concrete Installation: Hang top bracket first (subtracting 1/2"
from top of screen to mark corner edge of top of bracket).
Pre-drill 3 holes into concrete with 1/4" concrete bit and insert
concrete anchors. Position top bracket over holes and insert
5X40mm Philips head screws and washers.
• Let the bottom bracket drop and, while pulling tethers taut ,
mark locations for screws. Repeat mounting procedure
used with the top bracket. For best support, 3 screws per
bracket should be used.
Drywall
Concrete
• Start by lifting screen frame onto top bracket, letting the
bottom rest against bottom bracket. Carefully lift bottom of
screen onto bottom bracket (Figure A & B). Security clips
will lock bottom of screen in place. Installation is complete.
• To release, simply push in clips and carefully lift bottom of
screen up and away from wall.
B
A
A
B
D
C
E
A
B
C
D
E
DF-SL-84-MW / HC
84"
41.14''
73.19''
47.48''
79.53''
DF-SL-92-MW / HC
92"
45.08''
80.2''
51.42''
86.54''
DF-SL-100-MW / HC 100" 49.02''
87.17''
55.35''
93.5''
DF-SL-106-MW / HC 106" 51.93''
92.36''
58.27''
98.7''
DF-SL-110-MW / HC 110"
53.9''
95.87''
60.24''
102.2''
DF-SL-120-MW / HC 120" 58.82'' 104.57'' 65.16''
110.9''
DF-SL-133-MW / HC 133"
65.2''
116''
71.54'' 122.24'' 71.38''
Care and cleaning
• Your new screen can be effectively cleaned with a soft cloth
using mild soap and water. DO NOT use harsh detergents,
chemicals, distilled spirits or petro-chemicals to clean the
screen; doing so may result in severe damage to the screen or
the frame coating.
• If the felt covering on the frame gets dusty or covered with
lint, use a household vacuum cleaner with a brush or furniture
cleaning attachment to clean the felt. We do not recommend
using excessive amounts of water on the felt.
Fixed Film Screen with Black Velvet Frame
F
F
47.36''
51.3''
55.24''
58.15''
60.12''
65''
Assembly
&
Installation
Instructions