AirStage ASHA007GTAH Посібник з монтажу - Сторінка 4

Переглянути онлайн або завантажити pdf Посібник з монтажу для Кондиціонер AirStage ASHA007GTAH. AirStage ASHA007GTAH 15 сторінок. Indoor unit (floor type)
Також для AirStage ASHA007GTAH: Посібник з експлуатації (8 сторінок)

Друкувати сторінку

3.2. Installation dimension

004/007/009 model

80 mm or

more (*1)

Left side

70 mm or

more (*2)

1500 mm

or more

030/034 model

Left side

80 mm or

70 mm or more

more (*1)

(*2)

1500 mm or more

1800 mm or

*1: The distance between the wall hook bracket and the ceiling.

*2: The distance between the wall hook bracket and the side wall.

3.3. Installing the unit

Install the air conditioner in a location which can withstand a load of at least 5 times the

weight of the main unit and which will not amplify sound or vibration. If the installation

location is not strong enough, the indoor unit may fall and cause injuries.

If the job is done with the panel frame only, there is a risk that the unit will come loose.

Please take care.

3.3.1 Determining the piping direction

The piping can be connected

according to the figure and table.

When the piping is connected

in direction (B), (C), (D) or (E),

cut along the piping groove in

the side of the front panel with a

hacksaw.

Model

(A)

(B)

Rear

Right

outlet

004/007/009

Good

030/034

Good

3.3.2 Installing the wall hook bracket

• Refer to figure below for the installation hole dimensions of the wall hook bracket.

• Before fastening the wall hook bracket to the wall with the screws, level it by tapping the

hook at the center of bracket to the wall with the handle of a screwdriver.

(1) Fasten the wall hook bracket to the wall with 5 or more screws and anchor bolts

through the holes near the outer edge of the bracket.

(Do not install the wall hook bracket at only 1 place or at an angle.)

(2) For a concrete wall, embed anchor bolts (10 mm dia.) into the wall at the wall hook

bracket holes.

(Allow the anchor bolts to stick out at least 18 mm from the wall. Use 2 bolts for flat

concrete wall and 4 bolts for blister concrete wall.)

(3) Install the nuts to the anchor bolts through the wall hook bracket.

(4) Finally tighten the bolts and wood screws after confirming, using the level indicator,

that the clamp is horizontal.

Install the wall hook bracket level, both horizontally and vertically. If the wall hook

bracket is tilted, wa ter will drip to the floor.

As the weight of the indoor unit is 15 to 18 kg, it should be installed after properly exam-

ining the place where it is in tended to be in stalled. If the place is not strong enough, a

plank or girder should be used to make the place sufficiently strong so that the wall can

support the weight.

En-3

Wall hook bracket

Right side

200 mm or

more (*2)

1800 mm or

Wall cap

Wall hook bracket

Right side 200

mm or more (*2)

Wall cap

WARNING

(B)

(A)

(C)

(D)

(E)

(F)

Bottom

Left

Center

outlet

bottom

outlet

Good

WARNING

004/007/009 model

030/034 model

3.3.3 Cutting the hole in the wall for the connecting piping

(1) Cut a hole in the wall at the position shown in the following.

(2) Cut the hole so that the outside end is lower (5 to 10 mm) than the inside end.

(3) Always align the center of the wall hole. If misaligned, water leakage will occur.

(4) Cut the wall pipe to match the wall thickness, stick it into the wall cap, fasten the cap

with vinyl tape, and stick the pipe through the hole.

(5) For left piping and right piping, cut the hole a little lower so that drain water will flow

freely.

004/007/009 model

030/034 model

(E)

(G)

Lower

(F)

(D)

10 mm

(G)

or more

Left rear

outlet

Attach the wall pipe

―

Good

If the wall pipe is not used, the

Good

cable interconnecting the indoor

and outdoor units may touch

metal and cause electric leakage.

3.3.4 Attach the drain hose insulation (030/034 model only)

• Wrap the insulation around the

drain hose, making sure that

there are no gaps.

• Attach the Insulation (Drain

hose) to the drain hose.

Wall hook bracket

Tapping screw

(accessory, 5 pcs)

Wall hook bracket

Center mark

65 mm dia. hole

Wall hook bracket

80 mm dia. hole

Fasten with vinyl

tape

WARNING

Wall cap*

Drain hose

Tapping screw

(accessory, 8 pcs)

65 mm dia. hole

Center mark

Lower

10 mm

or more

5 to 10 mm

low

Wall pipe*

* Locally

purchased

(Inside)

Wall

(Outside)

Insulation (Drain hose)

(Accessories)