Motorized FlexShade
Improper installation and use of Motorized FlexShade can result in serious injury or death.
Primarily, injuries can occur when the Motorized FlexShade falls due to imprecise installation, mishandling of the Motorized FlexShade during installation
or installation on an insufficient wall or ceiling structure. Please use extreme care.
1. Please read the following installation guidelines thoroughly and follow them carefully.
Failure to do so may cause product to fall or otherwise fail, and could result in serious injury.
2. Installation and calibration of the Motorized FlexShade should only be performed by an authorized, qualified, and experienced professional.
In particular, electrical work and wiring [indicated in diagram by dashed lines] must be completed only by a qualified professional electrician who has
read this manual completely and is familiar with the construction and operation of this equipment and the hazards involved.
3. Do not affix the unit to wall or ceilings that have inadequate strength to permanently hold the unit during use.
It is the owner's and installer's responsibility to confirm the wall or ceiling to which the unit attaches is sufficient to permanently hold the weight and
stress loads of the unit at all times. Draper, Inc., is not responsible for improper installation, application, testing or workmanship related to the product
at place of installation.
4. It is the installer's responsibility to make sure appropriate fasteners are used for mounting.
5. All brackets, fascia, head boxes, pockets, wall clips, and other hardware must be installed level. Motorized FlexShade must be level and square.
6. Never leave the area while operating the Motorized FlexShade during installation, maintenance, or normal operation, unless it is secure and safe.
7. Before testing or operation, carefully inspect the entire area and path of the shade and areas underneath the shade to be sure no persons or objects
are in the area.
8. Turn off power and any nearby equipment or cables carrying electricity before connecting switches, wires, controls, or electrical components.
9. Make sure the limit switches are pointed down or accessible when placing the motor in brackets/endcaps.
10. All motors should be tested and limits set using test cord before shades are wired.
11. Do not wire motors in parallel without written permission from Draper, Inc.
12. During testing or operation, carefully watch the surrounding area for any potential safety concerns including nearby persons or objects.
13. After installation, the entire system, including all sensors, should be carefully tested to ensure safe and normal operation.
Extreme care should be taken during testing to remain clear of moving parts to avoid possible injury.
14. Operation of Motorized FlexShade should be performed only by authorized and qualified personnel, who have been trained in the safe and effective
operation of the Motorized FlexShade & understand its safety features.
15. The safety features of the Motorized FlexShade, including sensors, should never be disabled, bypassed or overridden.
The system should not be operated until all safety features, including the sensors, are properly and completely installed, calibrated and tested.
16. Motorized FlexShade may need to comply with local, state or district rules and regulations, in particular when installed in schools.
All applicable rules and regulations should be reviewed before installation and use.
17. Failure to precisely follow installation guidelines invalidates all warranties.
18. Custom products/installations may not be reflected in this manual. Call Draper, Inc., if you have questions about the installation of custom products
or any questions about your installation.
1. Look for any job site conditions that could interfere with installation or operation of the system.
2. Read carefully and be sure to understand all installation instructions and all related operations manuals.
These instructions are intended to as a guide for the installer and owner.
They should be followed closely and combined with the expertise of experienced qualified installers.
Draper, Inc., is not responsible for improper installation, application, testing or workmanship related to the product at place of installation.
Please retain all instructions for future use.
3. Open cartons lengthwise.
4. Locate and lay out all pieces.
5. Inspect all boxes to make sure you have received the proper Motorized FlexShade and parts.
Controls may be shipped separately, or in same carton as Motorized FlexShade.
6. If you have any difficulties with installing, servicing or operating your Motorized FlexShade, call your dealer or Draper, Inc., (765) 987-7999.
®
Important Safety Information
WARNING
Before Beginning Installation
INSTRUCTIONS
INSTALLATION & OPERATION
Друкувати сторінку