Draper Silhouette/Series E Інструкція з монтажу та експлуатації - Сторінка 5
Переглянути онлайн або завантажити pdf Інструкція з монтажу та експлуатації для Проекційний екран Draper Silhouette/Series E. Draper Silhouette/Series E 5 сторінок. Electric projection screen
Також для Draper Silhouette/Series E: Інструкція з монтажу та експлуатації (5 сторінок)
Друкувати сторінку
220V Silhouette/Series E & V by Draper
Back of wall switch.
Please Note: 5V DC must be
connected to be able to set
limits using the wall switch.
Please Note: Although both
Dry Contact and Data Cable
connections are shown, you
should only use one connec-
tion type per motor.
ILT Switch-to-Motor—Dry Contacts or Data Cable connection
External Low Voltage & Wireless Control
Two-Way Serial Communication (RS232) with MC1
White or Blue-Common
Red-to Screen (directional)
Black-to Screen (directional)
Brown-Hot to AC
Program LED
Green/Yellow-Ground
Fuse
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
Eye Port for IR Eye. For RF Receiver or LED
MC1
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
Wiring Diagram for Optional, Built-in Video Interface Control
Built-in Video Interface Control
220 VAC supply
Trigger signal
VIC220 (220 VAC, white cord & plug)
VIC12 (12 VDC, brown & orange leads)
www.draperinc.com
INSERT MOTOR DATA
CABLE HERE
White or Blue-Common to screen & 110/220V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110/220V AC-Hot
Black-to 110/220V AC-Hot
Green/Yellow (Ground)
Dashed wiring by electrician
Low voltage wiring by others
Eye Port for IR Eye, RF Receiver or LED
Wall Switch. For more than one of
these, a splitter is required.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Aux Port for connecting additional LVC-III
modules (up to six total can be linked-
connect from Aux to Eye).
Low Voltage Wiring by others
AC Wiring by electrician
To AC Line
Junction box at
left end of screen
Internal screen wiring
N
L1
Dashed wiring
by electrician
(765) 987-7999
Please Note: This Splitter/
Jack is located inside the junc-
tion box of your screen.
Data Cables to switches or
to additional motors can
be plugged into any of the
three open jacks. If this is a
"Case First, Screen Later"
installation, plug the motor
cable into the jack indicated
in the drawing.
Internal Screen Wiring
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Green/Yellow
(Motor Ground)
To
110/220V
Line
STOP
Location of key
operated on-off
switch if furnished
STOP
Control
Switches
24v DC
Internal Screen Wiring
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Green 110V/
Green/Yellow 220V
(Motor Ground)
See separate Serial Communica-
tion-RS232 Instruction sheet for
Location of key
enabling RS232 with the MC1.
operated on-off
switch if furnished
Blue (Neutral)
Black (Hot)
Green/Yellow (Ground)
Page 5 of 5