Draper Targa Інструкція з монтажу та експлуатації

Друкувати сторінку

Draper Targa Інструкція з монтажу та експлуатації

➀

Read instructions through completely before proceeding.

➁

Follow instructions carefully. Installation con trary to instructions in val i-

dates warranty.

➂

Screen should be accessible for complete removal should fabric be-

come damaged or should other ser vice be required.

➃

Screen should be installed level (using a carpenter's level).

➄

Nothing should be fastened to screen dowel or viewing surface.

➅

Operating switch(es) packed separately in screen carton. Do not dis-

card with packing material.

➆

Screen operates on 110-120v, 60 hz. current.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

These instructions are meant as a guide only. They do not imply any

re spon si bil i ty on the part of Draper, Inc. for improper in stal la tion or faulty

work man ship at the jobsite.

Hanging Screen

General:

When locating view ing surface and checking clear ance for screen's op er a tion, re-

member surface is centered in case. Handle case care ful ly to protect its ﬁ nish.

Regardless of mounting method, screen should be positively and securely sup-

port ed so that vibration or even abusive pulling on the viewing surface will not

cause case to work loose or fall. Installer must insure that fas ten ers used are of

adequate strength and suit able for the mounting sur face cho sen.

Suspended Installation:

Suspend screens from holes in endcaps as shown. "S" hooks are included,

but chains (or cable) and turn buck les should be provided by installer. Chains

should be attached to beams or other struc tur al mem bers. Turn buck les should

be adjusted so screen hangs level.

Wall Installation:

Mount screen through holes in back of endcaps as shown. Installer should

furnish screws, toggle bolts, molly bolts, nylon or lead anchors as required.

Recessed Installation:

Recess should permit access for removal of screen if necessary. Screen may

be mounted as in suspended or wall installation. Optional Ceiling Opening

Trim Kit available; see diagrams below and on page 2, and separate instruction

sheet (included with Ceiling Opening Trim Kit).

Screen Case

Installation/Operating Instructions

Targa Electric Projection Screen by Draper

Caution

Back

Ceiling Tile

(By others)

Form Targa_Inst04-R

Screen operates on 110-120v, 60 hz. current.

Junction box is located inside left endcap and cover plate is secured to endcap

with two screws. Junction box contains red, black and white pigtail leads and

green internal ground wire, per wiring di a gram on reverse.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire connecting screen to switch(es) and switch(es) to power supply

should be furnished by installer. Connections should be made in ac cor dance

with attached wiring diagram, and wiring should comply with National and local

electrical codes.

All operating switches should be "off" before power is connected.

Before operating screen remove tape securing fabric and dowel to roller. If

viewing surface hangs out of case 8"-9", tape has prob a bly been bro ken by

rough handling in ship ment, allowing surface to "un wrap" one turn about the

roller. Manually wrap fabric back around the roller without turning the roller

itself.

110-120v Single Station Control — 3-position up-off-down switch per mits op-

er a tion to be stopped at any point. Factory adjusted limit switch es au to mat i cal ly

stop screen when fully down or fully up.

110-120v Multiple Station Control—Switches are similar in ap pear ance to

110-120v Single Station Control. Screen stops when switch is re leased and

may be re start ed in either direction. Factory adjusted limit switch es stop screen

automatically when fully up or fully down.

24v Control — Three-button up-stop-down switch es stop at any point de sired,

operate in any sequence. Factory adjusted limit switches au to mat i cal ly stop

screen when fully up or fully down.

Key Operated Switching — Two kinds of key-operated switches are op tion al ly

available with this unit.

➀

The key-operated power sup ply switch controls power to the screen and

switches. When it is "off ", the switch es will not operate screen. Key may

be re moved from the switch in either "on" or "off" position.

➁

A three-po si tion key switch per mits the screen to be operated directly by

key. In this case, the screen's operator must always have a key.

Screen has been factory set and should not nor mal ly require further ad just -

ment. However, if you desire to change the "up" and "down" stop ping po si tions,

proceed as follows:

CAUTION: Be sure all switches are in "off " position before ad just ing limit

switches. Always be pre pared to shut screen off man u al ly when new adjust-

ment is being tested. Screen may be se vere ly dam aged if viewing surface is

al lowed to run too far up or too far down.

Adjusting "fully up" position — "Up" stopping position may be ad just ed by

turning the yellow limit switch adjustment socket. The yellow socket is lo cat ed

on left end of screen roller and is accessible to a screwdriver/Allen wrench

(4mm or

"). Turn ing the socket coun ter clock wise will allow the view ing sur-

face to retract farther into the case. Turn ing it clockwise will cause the sur face

to stop farther out of the case. One full revolution of the socket will alter the

stop ping position of the view ing surface by ap prox i mate ly 1½".

Adjusting "fully down" position — "Down" stopping position may be adjusted

by turning the white limit switch adjustment socket. The white socket is located

on the left end of screen roller and is accessible to a screw driv er/Allen wrench

(4mm or

"). Turning the socket coun ter clock wise will allow the viewing sur-

face to run farther down. Turning it clockwise will shorten the viewing surface,

causing it to stop in a less extended po si tion. At no time should viewing surface

be unrolled enough to expose any part of screen roller.

If you encounter any difﬁ culties installing or ser vic ing your Targa

screen, call your dealer or Draper Inc., Spiceland, Indiana, (765)

Printed in U.S.A.

987-7999, fax (765) 987-7142 or e-mail [email protected].

Electrical Connections

Operation

Adjustments