Bosch WAE24368GB Інструкція з експлуатації - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Пральна машина Bosch WAE24368GB. Bosch WAE24368GB 8 сторінок. Front-load washing machine
Також для Bosch WAE24368GB: Інструкція з монтажу Посібник з монтажу (6 сторінок)
Друкувати сторінку
Safety instructions
Care
– Read the instruction manual and installation instructions and all other information enclosed
with the washing machine and act accordingly.
– Retain the documents for subsequent use.
Risk of electric shock
– Never pull the cable to disconnect the mains plug.
– Never insert/disconnect the mains plug with damp hands.
Danger to life
For worn-out appliances:
– Disconnect the mains plug.
– Sever the mains cable and discard along with the plug.
– Destroy the lock on the washing machine door. This will prevent
children from locking themselves in and risking their lives.
Danger of suffocation
– Keep packaging, film and packaging parts out of the reach of
children.
Risk of poisoning
– Keep detergents and care products out of the reach of children.
Risk of explosion
– Items of laundry pretreated with cleaning agents containing
solvents, e.g. stain remover / cleaning solvent may lead to an
1. Pull out, press insert down, remove draw completely.
explosion after being loaded into the washing machine.
2. To remove the insert: press the insert upwards from below with your finger.
Rinse items of laundry thoroughly by hand beforehand.
3. Clean the detergent dispenser tray and insert with water and a brush and dry it.
4. Attach the insert and engage (connect the cylinder to the guide pin).
Risk of injury
– The washing machine door can become very hot.
5. Push in the detergent drawer.
– Be careful when draining hot detergent solution.
– Do not climb onto the washing machine.
– Do not lean on the open washing machine door.
– Do not reach into the drum if it is still rotating.
– Be careful when opening the detergent drawer while the machine
is in operation.
Consumption values
depending on model
Programme
Programme
Load
Electricity***
Water***
duration***
Cottons 30 °C*
7 kg
0,55 kWh
60 l
02:36 h
Cottons 40 °C*
7 kg
0,69 kWh
60 l
02:36 h
Cottons 60 °C*
7 kg
1,33 kWh
60 l
02:41 h
Cottons 90 °C
7 kg
2,00 kWh
64 l
02:48 h
Easy-Care 40 °C*
3 kg
0,55 kWh
55 l
01:37 h
Mixed Load 40 °C
3 kg
0,48 kWh
32 l
01:03 h
Delicate/Silk 30 °C
2 kg
0,21 kWh
31 l
00:41 h
1. Turn the programme selector to Off and disconnect the mains plug.
2. Drain the detergent solution
/ Wool 30 °C
2 kg
0,19 kWh
39 l
00:40 h
3. Pull the emergency release downwards with a tool and release.
* Programme setting for testing in accordance with valid standard EN60456.
Note on comparative tests: For testing the test programmes, wash the specified load using the maximum spin speed.
Annual energy
Annual water
Information on the display panel
Programme
Additional function
Load
consumption
consumption
Cottons 40/60 °C
EcoPerfect**
7/3,5 kg
197 kWh
10560 l
F: 16
F: 17
** Programme setting for testing and energy labelling in accordance with EU directive 2010/30/EU with cold water (15 ºC).
*** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient tem-
perature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional
F: 18
functions.
F: 21
F: 23
7
8
– Risk of electric shock. Disconnect the mains plug.
Maintenance
– Risk of explosion. No solvents.
Before washing for the first time
Detergent solution pump
Do not load any laundry into the machine. Turn on the tap. Add the following to compartment II:
Turn the programme selector to Off and disconnect the mains plug.
– approx. 1 litre water
1. Open and remove the service flap.
– detergent (dosage according to the manufacturer's instructions for light soiling and the appropriate degree of water
hardness)
Set the programme selector to
Easy-Care 60 °C and select
Start/Reload. At the end of the programme, turn
the programme selector to Off.
2. For models with a drainage hose: Remove the drainage hose from the retainer and pull it
Machine housing, control panel
from the housing. Remove the container.
Remove the sealing cap, allow the detergent solution to flow out.
– Wipe with a soft, damp cloth.
Replace the sealing cap and place the drainage hose in the retainer.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Remove detergent and cleaning agent residue immediately.
– Do not clean with a jet of water.
2* For models without a drainage hose: Carefully unscrew the pump cover until the
detergent solution begins to flow out. When the service flap is half full, close the pump cover
Cleaning the detergent drawer ...
and empty the service flap. Repeat the above steps until all the detergent solution has
... if it contains detergent or fabric softener residues.
completely drained out.
3. Carefully unscrew the pump cover (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller in the detergent
solution pump must rotate).
5. Replace the pump cover and screw it tightly.
6. Place the service flap back on and close.
Leave the detergent drawer open so that any residual water can evaporate.
To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into
Drum
compartment II and start the
Leave the washing machine door open so that the drum can dry out.
Drainage hose at the siphon
Rust stains - use chlorine-free cleaning agent, not steel wool.
Turn the programme selector to Off and disconnect the mains plug.
Descaling
Ensure there is no laundry in the machine
1. Loosen the hose clamp, carefully remove the drainage hose (residual water).
Descale the appliance according to the descaler manufacturer's instructions. This should not be necessary if the
2. Clean the drainage hose and siphon connecting piece.
correct dosage of detergent is used.
3. Reattach the drainage hose and secure the connection with the hose clamp.
Emergency release, e.g. in the event of a power cut
Filter in the water supply
The programme continues to run when the power has been restored. However, if the laundry has to be removed, the
Risk of electric shock!
washing machine door can be opened as follows:
Do not immerse the HydroSafe safety device in water (contains an electric valve).
Risk of scalding.
The detergent solution and laundry may be hot. If possible, leave it to cool down.
Reduce the water pressure in the supply hose:
Do not reach into the drum if it is still rotating.
1. Turn off the tap.
Do not open the washing machine door if water can be seen through the glass.
2. Select any programme (except for
3. Choose
Start/Reload. Let the programme run for approximately 40 seconds.
page 10.
4. Turn the programme selector to Off. Disconnect the mains plug.
Washing machine door can then be opened.
Clean the filter:
1. Depending on model:
depending on model
Disconnect the hose from the tap.
Clean the filter using a small brush.
Close the washing machine door properly; laundry may be caught.
Open the tap completely, supply hose kinked or trapped;
and/or for Standard and Aqua-Secure models:
Clean the filter
page 10, Water pressure too low.
Remove the hose on the rear of the appliance,
Detergent solution pump blocked; Clean the detergent solution pump
page 10. Drainage hose / waste pipe
Remove the filter with pliers and clean.
blocked; Clean the drainage hose at the siphon
page 10.
2. Connect the hose and check for leaks.
Motor fault. Call customer services.
Water in the base tub, appliance leaking. Call customer services.
9
– Risk of scalding.
What to do if ...
Allow the detergent solution to cool down.
– Turn off the tap.
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
No water supply.
–
Start/Reload not selected?
Detergent not
– Tap not turned on?
dispensed.
– Filter blocked? Clean the filter
– Supply hose kinked or trapped?
Washing machine door
– Safety function active. Programme stopped?
cannot be opened.
– Is Rinse Hold (without final spin) selected?
– Can be opened by emergency release only?
Programme does not
–
Start/Reload or
start.
– Washing machine door closed?
– Childproof lock active? Deactivate
Detergent solution is
– Is Rinse Hold (without final spin) selected?
not drained.
– Clean the detergent solution pump
– Clean the waste pipe and/or drainage hose.
Water not visible in the
– Not a fault - water below the visible area.
drum.
Unsatisfactory spin
– Not a fault - the unbalanced-load detection system has cancelled the
result.
spin cycle because of uneven distribution of the laundry.
Laundry wet/too damp.
Distribute small and large items of laundry evenly inside the drum.
–
Reduced Ironing selected?
– Selected speed too low?
The programme
– Not a fault – the programme sequence is optimised for the particular
duration changes
wash process. This may result in changes to the programme duration
during the wash cycle.
in the display field.
Drain programme.
Spin cycle performed
– Not a fault - unbalanced load detection system adjusts the
several times.
imbalance.
Residual water in the
– Not a fault - the action of the care product is not affected.
compartment for care
– Clean the insert if necessary
products.
Odour formation in the
– Run programme
washing machine.
detergent.
Status display
– Too much detergent used? Mix 1 tablespoon of fabric softener with
flashes. Foam may be
½ litre of water and pour into dispenser II (not for outdoor and down-
coming out of the
filled textiles!).
detergent drawer.
– Reduce the detergent dosage for the next wash cycle.
Intense noise
– Are the appliance feet fixed?
formation, vibrations
Secure the appliance feet
and "wandering"
– Transportation safety devices removed? Remove the transportation
during the spin cycle.
safety devices
Rinse/
Spin //
Drain).
Noises during spin and
– Clean detergent-solution pump
drain cycles.
Display panel/indicator
– Power cut?
lamps do not function
– Fuses triggered? Reset/change the fuse.
during operation.
– If the fault occurs repeatedly, call customer services.
Programme sequence
– Not a fault - unbalanced load detection system adjusts imbalance by
longer than usual.
repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse
cycle.
Detergent residues
– Occasionally, phosphate-free detergents contain water-insoluble
on the laundry.
residues.
– Select the
Rinse/
washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
10
– Turn off the water supply and call customer services
page 10.
page 4.
page 3, 4.
page 9.
Ready in time selected?
page 5.
page 3, 4.
page 10.
page 5.
page 5.
page 9.
Cottons 90 °C without laundry. Use standard
Installation instructions.
Washing machine
Installation instructions.
page 10.
en Instruction manual
Spin cycle or brush out the laundry after
Installation instructions.
11