Bosch WAE28267SN Інструкція з експлуатації Посібник з експлуатації - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція з експлуатації Посібник з експлуатації для Пральна машина Bosch WAE28267SN. Bosch WAE28267SN 8 сторінок.
Друкувати сторінку
Safety instructions
Care
– Read the instruction manual and installation instructions and all other information enclosed with the washing
machine and act accordingly.
– Retain the documents for subsequent use.
Risk of electric shock
– Never pull the cable to disconnect the mains plug.
– Never insert/disconnect the mains plug with damp hands.
Danger to life
For worn-out appliances:
– Disconnect the mains plug.
– Sever the mains cable and discard along with the plug.
– Destroy the lock on the washing machine door. This will prevent children from
locking themselves in and risking their lives.
Danger of suffocation
– Keep packaging, film and packaging parts out of the reach of children.
Risk of poisoning
– Keep detergents and care products out of the reach of children.
Risk of explosion
– Items of laundry pretreated with cleaning agents containing solvents, e.g. stain
remover/cleaning solvent may cause an explosion after being loaded into the
washing machine.
Rinse items of laundry thoroughly by hand beforehand.
1. Pull the drawer out, press down the insert and fully remove the drawer
Risk of injury
– The washing machine door can become very hot.
2. To remove the insert: press the insert upwards from below with your
– Be careful when draining hot detergent solution.
– Do not climb onto the washing machine.
3. Clean the detergent dispenser tray and insert with water and a brush and
– Do not lean on the open washing machine door.
– Do not reach into the drum if it is still rotating.
– Be careful when opening the detergent drawer while the machine is in operation.
4. Attach the insert and engage (connect the cylinder to the guide pin).
5. Push in the detergent drawer.
Consumption values
depending on model
Programme
Programme
Load
Electricity**
Water**
duration**
Cottons 20 °C
7 kg
0,31 kWh
72 l
2 ¾ h
Cottons 40 °C
7 kg
0,85 kWh
72 l
2 ¾ h
Cottons 60 °C
7 kg
1,21 kWh
72 l
2 ¾ h
Cottons 90 °C
7 kg
2,01 kWh
77 l
3 h
Easy-Care 40 °C
3 kg
0,64 kWh
56 l
1 ¾ h
Mix 40 °C
3 kg
0,46 kWh
36 l
1 ¼ h
Information on the display panel
Delicates/Silk 30 °C
2 kg
0,24 kWh
37 l
¾ h
/ Wool 30 °C
2 kg
0,22 kWh
47 l
¾ h
E3
E5
Annual energy
Annual water
E6
Programme
Additional function
Load
consumption
consumption
Cottons
EcoPerfect 40/60 °C *
3,5/7 kg
165 kWh
10686 l
E2
* Programme setting for testing and energy labelling in accordance with EU directive 2010/30/EU with cold water (15 ºC).
** The values deviate from the indicated values depending on water pressure, hardness, and inlet temperature, ambient tem-
perature, type, amount and soiling of the laundry, detergent used, fluctuations in the power supply and selected additional
functions.
8
8
7
– Risk of electric shock.
Maintenance
Disconnect the mains plug.
– Risk of explosion. No solvents.
Before washing for the first time
Detergent solution pump
Do not load any laundry into the machine. Turn on the tap.
Turn the programme selector to Off and disconnect the mains plug.
Add the following to compartment II:
1. Open and remove the service flap.
– approx. 1 litre water
– detergent (dosage according to the manufacturer's instructions for light soiling and the
appropriate degree of water hardness)
Set the programme selector to
Easy-Care 60 °C and select
(Start/Pause). At the end
2. For models with a drainage hose: Remove the drainage hose from the
of the programme, turn the programme selector to Off.
retainer and pull it from the housing. Remove the container.
Remove the sealing cap, allow the detergent solution to flow out.
Machine housing, control panel
Replace the sealing cap and place the drainage hose in the retainer.
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
2* For models without a drainage hose: Carefully unscrew the pump cover
– Remove detergent and cleaning agent residue immediately.
until the detergent solution begins to flow out. When the service flap is
– Do not clean with a jet of water.
half full, close the pump cover and empty the service flap. Repeat the
Cleaning the detergent drawer and housing...
above steps until all the detergent solution has completely drained out.
... if it contains detergent or fabric softener residues.
3. Carefully unscrew the pump cover (residual water).
4. Clean the interior, pump cover thread and pump housing (the impeller in
from the housing.
the detergent solution pump must rotate).
finger.
5. Replace the pump cover and screw it tightly.
6. Place the service flap back on and close.
dry it. Also remove any detergent or fabric softener residues in the
housing.
To prevent unused detergent from flowing straight into the drain during the next wash:
Pour 1 litre of water into compartment II and start the
Drainage hose at the siphon
Leave the detergent drawer open so that any residual water can
evaporate.
Turn the programme selector to Off and disconnect the mains plug.
Washing drum and rubber seal
1. Loosen the hose clamp, carefully remove the drainage hose
(residual water).
Wipe the inside of the rubber seal dry with a cloth. Leave the washing machine door open so
2. Clean the drainage hose and siphon connecting piece.
that the drum can dry out. Rust stains - use chlorine-free cleaning agent, not steel wool.
3. Reattach the drainage hose and secure the connection with the hose
Descaling
Ensure there is no laundry in the machine
clamp.
Descale the appliance according to the descaler manufacturer's instructions. This should not
Filter in the water supply
be necessary if the correct dosage of detergent is used.
Risk of electric shock
Do not immerse the HydroSafe safety device in water (contains an electric valve).
Reduce the water pressure in the supply hose:
depending on model
1. Turn off the tap.
Close the washing machine door properly; laundry may be caught.
2. Select any programme (except
Open the tap completely, supply hose kinked or trapped;
3. Select
(Start/Pause). Let the programme run for approximately
Clean the filter
page 10, Water pressure too low.
40 seconds.
Detergent solution pump blocked; Clean the detergent solution pump
page 10.
4. Turn the programme selector to Off. Disconnect the mains plug.
Drainage hose/waste pipe blocked; Clean the drainage hose at the siphon
page 10.
Clean the filter:
Motor fault. Call the after-sales service.
1. Depending on model:
Disconnect the hose from the tap.
Clean the filter using a small brush.
and/or for Standard and HydroSafe models:
Remove the hose on the rear of the appliance,
Remove the filter with pliers and clean.
2. Connect the hose and check for leaks.
9
– Risk of scalding.
What to do if ...
Allow the detergent solution to cool down.
– Turn off the tap.
Water is leaking out.
– Attach/replace the drainage hose correctly.
– Tighten the screw connection of the supply hose.
No water supply.
–
(Start/Pause) not selected?
Detergent not
– Tap not turned on?
dispensed.
– Filter blocked? Clean the filter
– Supply hose kinked or trapped?
Washing machine door
– Safety function active. Wait approx. 2 minutes.
cannot be opened.
– - - - - (without final spin) selected?
Programme does not
–
(Start/Pause) or
start.
– Washing machine door closed?
– Childproof lock active? Deactivate
Detergent solution is
– - - - - (without final spin) selected?
not drained.
– Clean the detergent solution pump
– Clean the waste pipe and/or drainage hose.
Water not visible in the
– Not a fault - water below the visible area.
drum.
Unsatisfactory spin
– Not a fault - the unbalanced-load detection system has cancelled
result.
the spin cycle because of uneven distribution of the laundry.
Laundry wet/too damp.
Distribute small and large items of laundry evenly inside the drum.
– Programme
Easy-iron selected?
– Speed selected too low?
The programme
– Not a fault – the programme sequence is optimised for the
duration changes
particular wash process. This may result in changes to the
during the wash cycle.
programme duration in the display field.
Spin cycle performed
– Not a fault - unbalanced load detection system adjusts the
Drain programme.
several times.
imbalance.
Residual water in the
– Not a fault - the action of the care product is not affected.
compartment for care
– Clean the insert if necessary
products.
Odour formation in the
– Run programme
Cottons 90 °C without laundry. Use standard
washing machine.
detergent.
(Wash) display lamp
– Too much detergent used? Mix 1 tablespoon of fabric softener with
flashes. Foam may be
½ litre of water and pour into dispenser II (not for outdoor and
coming out of the
down-filled textiles!).
detergent drawer.
– Reduce the detergent dosage for the next wash cycle.
Intense noise formation,
– Are the appliance feet fixed?
vibrations and
Secure the appliance feet
"wandering" during the
– Transportation safety devices removed?
spin cycle.
Remove the transportation safety devices
instructions.
Noises during spin and
– Clean detergent-solution pump
Rinse/
Spin //
Drain).
drain cycles.
Display panel/indicator
– Power cut?
lamps do not function
– Fuses triggered? Reset/change the fuses.
during operation.
– If the fault occurs repeatedly, call the after-sales service.
Programme sequence
– Not a fault - unbalanced load detection system adjusts imbalance
longer than usual.
by repeatedly distributing the laundry.
– Not a fault - foam detection system active - adds an additional rinse
cycle.
Detergent residues on
– Occasionally, phosphate-free detergents contain water-insoluble
the laundry.
residues.
– Select
Rinse/
Spin or brush the laundry after washing.
If you cannot correct a fault yourself (switching on/off) or a repair is required:
– Turn the programme selector to Off and remove the mains plug from the socket.
– Turn off the water supply and call the after-sales service
10
page 10.
page 3, 4.
(Finished in) selected?
page 5.
page 3, 4.
page 10.
page 7.
page 5.
page 9.
Installation instructions.
Washing machine
Installation
WAE28267SN
page 10.
en operating instructions
Installation instructions.
11