FlexShade
®
Caution: Before mounting shades, verify measurements on label provided with shade, and ensure unit is installed at correct width.
Please Note: Installer is responsible for selecting mounting hardware appropriate for site conditions.
Section 1 - Brackets
1. Mark wall, jamb, or ceiling for placement of mounting brackets.
2. Drill small starter hole
(if necessary)
3. Mount brackets using appropriate fasteners for surface
4. Place spring-loaded pin into idler end bracket, depress pin by pushing
shade roller toward bracket, slip notches on operator end into other
bracket, then press down to lock in place
Figure 1a
"
24mm
Figure 1b
"
24mm
Figure 2a -
IDLER END
Section 3 - Fascia
1. Snap end covers onto endcaps.
2. Install endcaps and shade
3. Place groove along top of fascia over endcaps, and snap into place
Fascia is not fully seated until it clicks into place on both ends. Once in place,
secure with appropriate fastener
Figure 6
Recharge
in mounting surface.
(Fig. 1a-1b)
.
(Fig. 2a-2b)
Large
2 x 2
2 "
(73mm x 56mm)
57mm
2 "
17mm
73mm
2 "
56mm
1 "
48mm
"
24mm
Small
2 x 2
1 "
40mm
(60mm x 56mm)
2 "
17mm
60mm
2 "
56mm
1 "
30mm
"
24mm
Figure 2b -
OPERATOR END
.
(see Section 2—Endcaps)
if necessary.
(not included)
Section 2 - Endcaps
.
Figure 3
Figure 4 -
FLEXSHADE RECHARGE ENDCAP DIMENSIONS
"
3 "
3 "
(83 mm)
(83 mm)
2 "
70mm
2 "
2 "
(57 mm)
(57 mm)
4 "
4 "
(117 mm)
(117 mm)
2 "
2 "
(57 mm)
(57 mm)
3"
3"
(76 mm)
(76 mm)
4 "
4 "
(117 mm)
(117 mm)
"
LARGE
5. Place spring-loaded pin into idler endcap, depress pin by pushing shade
1 "
roller toward endcap, slip notches on operator end into operator endcap,
44mm
then press down to lock in place
Figure 5a -
IDLER END
Reverse Roll Fascia
1. Mark mounting points.
.
(Fig. 6)
2. Slide endcaps into extrusions.
3. Use pre-drilled endcap holes
to mark fascia for drilling.
4. Attach endcaps to fascia using
included hardware.
5. Mount Endcaps/Reverse Roll
Fascia.
6. Install roller/fabric/operator
assembly according to relevant
instructions.
7. Attach endcap covers to endcaps.
Use double-sided tape to help
secure in place.
Clicks into place
page 3 of 11
1. Snap end covers onto endcaps
.
(Fig. 3)
2. Mark wall, jamb, or ceiling for
placement of mounting endcaps.
3. Drill small starter hole
in mounting surface.
4. Mount endcaps using appropriate
fasteners for surface
2"
2"
(51 mm)
(51 mm)
"
"
(16 mm)
(16 mm)
1 "
1 "
(48 mm)
(48 mm)
3 "
3 "
3 "
3 "
3 "
3 "
(98 mm)
(98 mm)
(83 mm)
(83 mm)
(89 mm)
(89 mm)
1 "
1 "
(48 mm)
(48 mm)
2"
2"
(51 mm)
(51 mm)
3 "
3 "
(86 mm)
(86 mm)
SMALL
.
(Fig. 5a-5b)
Figure 5b -
OPERATOR END
Figure 7
(if necessary)
.
(Fig. 4)
"
"
(17.5 mm)
(17.5 mm)
2 "
2 "
2"
2"
(73 mm)
(73 mm)
(51 mm)
(51 mm)
Друкувати сторінку