Draper FlexShade Slim NEXD Інструкція з монтажу та експлуатації - Сторінка 5
Переглянути онлайн або завантажити pdf Інструкція з монтажу та експлуатації для Внутрішнє оздоблення приміщень Draper FlexShade Slim NEXD. Draper FlexShade Slim NEXD 7 сторінок.
Друкувати сторінку
Clutch-Operated FlexShade
Slim Hardware
Section 4 - Shade Fabric Roller Mounting
Caution: Do not allow shade roller to become exposed by running shade fabric too far down. Be sure to use stop balls provided in hardware packet by Draper to
set up and down travel limits. Stop balls by others may be too small, and become lodged in clutch mechanism.
Please Note: If shade fabric is uneven, see "Field Adjustments" on page 2.
1.
Carefully work open
(clutch) end of roller
onto bead chain
clutch.
!
Tube indentation
must be aligned
with the FLAT side
of the clutch sprocket.
Figure 6-A
Section 5- Bead Chain Limits and Safety Device Installation
Attaching Stop Balls
1. Set upper and lower travel limits by installing stop balls to bead chain
P-Clip Cord Tension Device
Please Note: Draper Bead Chain Clutch-Operated shades that do not comply with WMCA/ANSI
Standard A100.1-2012 come with a P Clip cord tension device pre-attached to bead chain
This device must be attached to wall, jamb, or sill so that bead chain is held taut enough that
children cannot pull it away from wall or fit their head into loop.
Spring-Loaded Cord Tension Device
If Draper Clutch FlexShade complies with WMCA/ANSI Standard A100.1-2018, a Spring-Loaded Cord
Tension Device comes installed on bead chain
mechanical fasteners
are included. Device is designed so that children cannot pull bead
(wood screws)
chain away from wall or fit their head into loop.
For more information, visit www.draperinc.com/WindowShades/WCMAcompliance.asp.
1. Install cord tension device to wall, jamb, or sill.
2. Pull tensioner down so that bead chain is held taut and use mounting hardware to keep it taut.
Please Note: Bead chain should be taut enough to move smoothly through device. However, overtightening
screws will damage Spring-Loaded Tension Device.
Section 6- Fascia
1. Place groove along top of fascia over endcaps.
2. Snap into place
.
(Fig. 10)
Please Note: Fascia is not fully seated until it clicks into place
on both ends. Once in place, check for secure fit.
NEXD,
®
(Fig. 6)
Figure 6-B
(crimp closed using pliers) (Fig. 7)
. An approved permanent warning label and approved
(Fig. 9)
.
(See safety note on page 2)
2.
Slide idler end
pin up through
one of the slots
3.
on idler endcap,
and into seat
for pin.
:
NOTE
See illustration
for different
path options.
4.
If not, adjust idler
leveling screw with
3mm Hex Wrench,
available upon
request when ordering shade.
CHAIN LIMITS
.
1. Attach
stop balls.
.
(Fig. 8)
Figure 7
CHAIN TENSION DEVICE
Sill
Mount
Insert fascia.
STEP 1
Figure 10
page 5 of 7
Test shade to
ensure that
roller is level
and operating
properly.
Figure 6-C
P-CLIP
P-Clip
2. Crimp
closed
with
pliers.
Figure 8
Jamb
Mount
Tensioner
Figure 9
STEP 2
Clicks
into place.