Draper Ultimate Access FlexShade Інструкція з монтажу та експлуатації - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція з монтажу та експлуатації для Внутрішнє оздоблення приміщень Draper Ultimate Access FlexShade. Draper Ultimate Access FlexShade 2 сторінки.
Друкувати сторінку
Ultimate Access FlexShade by Draper
10"
9
9
/
16
9
/
"
9
16
Limit Switch Adjustments
CAUTION: Be sure all switches are in "off" position before adjusting limit
switches. Always be pre pared to shut off man u al ly when new ad just ment is
being tested. Do not allow the shade roller to become exposed by run-
ning the shade fabric too far down. Shade may be se vere ly damaged if
allowed to run too far up or down. Each shade's lim it switch must be set if us-
ing group control system. Motor should be installed so limit switches are
pointed down or accessible.
Push Button Limits
① Fully depress both limit switch push buttons, then operate wall switch to
make sure system works properly.
② Raise shade to desired "up" stop position.
③ Set upper limit by depressing and releasing the proper (back) push button.
④ Lower shade to desired "down" stop position.
⑤ Set lower limit by depressing and releasing the proper (front) push button.
Screw-Type Limits
① Determine which direction of fabric travel corresponds with arrows on
motor.
② Operate shade to desired "down" stop position. Set limit by turning the
proper socket toward the "+" to lower the limit, and "-" to raise it.
③ Operate shade to desired "up" stopping position. Set limit by turning the
proper screw toward the "-" to raise the limit, and "+" to lower it.
Mounting Bracket Dimensions
3
/
"
1
/
"
1
1
/
"
8
2
2
R
1
/
"
4
1
/
"
8
1
3
/
"
8
1
/
"
4
5
/
"
16
R
1
/
"
8
9"
7½"
1"
"
5
/
"
8
8"
Ceiling tile
(by others)
13
6
/
"
16
4¾"
5
/
"
8
8"
3
/
"
16
1
4
/
"
2
1
1
/
"
4
4
13
/
"
16
3
7
/
"
4
9"
www.draperinc.com
Case Dimensions
Mounting brackets slide
left and right as needed.
Alternative mounting configuration
Idlers on motorized shades may occasionally need lubrication. If lubrica-
tion is required, apply a small amount of a lithium based grease direct to the
idler pin.
Most of Draper's standard fabrics may be cleaned at the window by
vacuuming with a soft brush attachment. They may also be cleaned by using
a sponge or soft cloth and mild solution of warm soapy water. A dishwashing
liquid, such as Ivory liquid, is recommended. A clean dry cloth is recommend-
ed for the metal fi nish. Exceptions are Flocké, Roc-Rol and Phifer SW7000
fabrics, which must be cleaned with a dry art sponge.
Wiring Diagram—Single Station Control *
5
/
"
16
3
/
"
16
1
1
/
"
8
1
/
"
4
To 110-120V Line
(765) 987-7999
Cleaning and Maintenance
Internal Shade Wiring
White (Common)
Black
Red
Green (Ground)
Do not wire motors in
parallel without written
permission from Draper.
Control
Single gang box by others
switch
1
Min. 4" x 2
/
" x 1
8
Red
Black
NOTE: Test shade op-
Black
eration. If shade direction
does not correspond with
the switch orientation,
turn power back off
then switch the red and
black wires from the mo-
Dashed wiring by electrician
tor to the switch.
* For Low Voltage or Multiple Station Control,
see diagrams provided with control.
Page 2 of 2
7
/
" deep
8