Bosch 2 Оригінальна інструкція з експлуатації - Сторінка 16

Друкувати сторінку

Bosch 2 Оригінальна інструкція з експлуатації

1. Starting Operation

OBJ_BUCH-412-001.book Page 35 Thursday, April 3, 2008 3:18 PM

Changing Application Tools on the

Screw Head with External Square Drive

When working with an application tool, pay

attention that the application tool is firmly

seated on the tool holder. When the applica-

tion tool is not firmly connected with the tool

holder, it can come loose again and not be

controlled.

ANGLE EXACT 2 | 3 | 6 | 7 | 7 – 900 | 8 |

10 – 650 | 14 – 420 | 15

An angled screw head with 1/4" square drive

(Article number 0 607 453 617) as well as one

with 3/8" square drive (Article number

0 607 453 620) are available for these industrial

cordless angle wrenches.

ANGLE EXACT 7 – 900 | 10 – 650 | 14 – 420 | 17 |

23 | 30

An angled screw head with 3/8" square drive

(Article number 0 607 451 618) is available for

these industrial cordless angle wrenches.

ANGLE EXACT 25 – 250 | 30 – 380 | 40 – 280 |

50 – 210

These industrial cordless angle wrenches are

supplied with a 3/8" sqaure drive angled screw

head.

Inserting

Press in the pin on the drive square of the tool

holder 2, e.g. using a small screwdriver, and

slide the tool bit 1 over the drive square. Pay at-

tention that the pin engages in the recess of the

tool bit.

Removing

Press in the pin in the recess of the tool bit 1

and pull the tool bit out of the tool holder 2.

Bosch Power Tools

Changing Application Tools on the

Screw Head with Internal Hexagon

(see figure F)

When working with an application tool, pay

attention that the application tool is firmly

seated on the tool holder. When the applica-

tion tool is not firmly connected with the tool

holder, it can come loose again and not be

controlled.

ANGLE EXACT 2 | 3 | 6 | 7 | 7 – 900 | 8 |

10 – 650 | 14 – 420 | 15

An angled screw head with 1/4" internal hexa-

gon (Article number 0 607 453 618) is available

for these industrial cordless angle wrenches.

Inserting

Insert the tool bit 1 into the internal hex socket

of the tool holder 2 until it can be felt to engage.

Removing

Pull the tool bit 1 off of the tool holder 2 with

the aid of pliers, if necessary.

Operation

Use safety equipment. Always wear

eye protection. Safety equipment

such as dusk mask, non-skid safety

shoes, hard hat, or hearing protec-

tion used for appropriate conditions

will reduce personal injuries.

Starting Operation

When starting the power tool, you should first

select the direction of rotation with the rotation-

al direction switch 14 since the power tool

starts only when the rotational direction switch

14 is not in the middle position (switch-on lock).

Reversing the Rotational Direction

(see figure G)

Right rotation: For driving in screws, push the

rotational direction switch 14 left to the stop.

Left Rotation: For loosening or unscrewing

screws, push the rotational direction switch 14

right to the stop.

Actuate the rotational direction switch 14

only when the machine is at a standstill.

English | 35

3 609 929 B34 | (3.4.08)