BDI AES-403 Технічний довідник - Сторінка 5

Переглянути онлайн або завантажити pdf Технічний довідник для Перемикач BDI AES-403. BDI AES-403 10 сторінок. Multi switcher digital/analog input audio switcher/da/digital to analog converter

Друкувати сторінку

Initial Power Application

Once power is applied and a valid AES bit stream is applied to the selected input or if the unit is

configured to select an analog input and B input is selected, the unit will default to "MAN" mode of

operation. The LED indicator over the "MAN" button should be illuminated. In addition, the

channel selected LED indicator will be lit or flashing which indicates audio level under threshold

for at least 15 seconds. This feature allows the user to determine if audio level is sufficient to

drive the unit or for troubleshooting purposes. This feature can be defeated if desired by setting

DIP SW1-6 to the OFF position. In the OFF position the unit will always indicate channel selection

with a steady lighted indication. There should also be an indication of sample frequency if a digital

input is selected. When the unit is configured for analog input on input B the front panel sample

rate indication will be that which was selected upon configuration. When a digital input is selected

the sample rate indication will be that which is input on the selected digital input. The AES-403

supports any sample rate between 32 and 192 KHz for digital I/O. The AES-403 supports 32,

44.1 or 48 KHz for analog inputs which are configured upon initial installation. Factory default is

44.1 KHz sampling for analog input. Standard sample rates are indicated on the front panel

under "Sample Rate" and non standard sample rates are indicated with the "OTHER" LED

indication being illuminated. Press the error-reset button to clear any errors that might be

indicated. If the digital audio stream feeding the active channel of the unit is valid and no errors

occur the unit is ready for to be placed in the automatic mode if desired. If any of these errors

occur after depressing the error-reset button, then the feed to the unit is defective and should be

investigated. If all is in order, the unit is now ready for operation. All that is left to do is to select

the desired feed and then if desired, place the unit in automatic switch mode by depressing the

"AUTO" mode button. The LED indicator will light indicating automatic control of the switcher. The

unit will remain in this mode until an error is detected, loss of lock occurs, silence or is detected. If

any of these events occur, the unit will switch to the alternate path and remain there until the error

reset is performed from the front panel or remotely. When in AUTO mode and an error occurs the

unit will go to manual mode and the "MAN" button and error indication will flash to indicate that

an error has occurred. To clear the error, depress the "ERROR" button. If the error clears the

"ERROR" button LED will extinguish, error indicators will extinguish and the "MAN" button will

remain illuminated until the "AUTO" button is depressed.

Description of AES-403 Optional Programming Functions

S1-1 Front Panel Button Defeat – When set to on will cause the A/B, MAN and AUTO buttons to

be non operational. Rear panel GPIO and serial remote control are still available when this switch

is turned on.

S1 -2, 3 Time Delay – Sets the time delay that the silence sensor will wait before switching. Time

delay can be set to 30, 60, 90 or 120 seconds.

S1-4, 5 Silence Detector Channel – Can be set to monitor both (L+R) or left only/right only.

When set to both, the silence detector will switch to the alternate path if one or both channels

signal level fall below threshold for the time delay set. For Left or Right only the silence sensor

will only switch after the channel being monitored times out. The unselected channel is ignored.

S1-6 Silence Indication on A/B Buttons – Will cause the selected channel button to flash if

audio level falls below threshold for more than 15 seconds. Set to off for steady on condition of

A/B buttons.

S1-8 Serial Remote Control – Turns on serial remote control functionality.

S2-1 AES ERROR Switching delay – when enabled ignores all momentary digital errors under 5

seconds in duration – eliminates inadvertent switching on transient events. When switched to off