Drayton 30002 Посібник з монтажу - Сторінка 2

Переглянути онлайн або завантажити pdf Посібник з монтажу для Терморегулятор Drayton 30002. Drayton 30002 2 сторінки. Digistat+ & digistat+rf room thermostat
Також для Drayton 30002: Посібник з монтажу (3 сторінок)

Друкувати сторінку

ºc

p I

To cancel the Preset Mode & return to normal operation

You can either,

7 0

ºc

p I

1. If you want to return to your previous setpoint (before you entered

the Preset mode) then press the 'SET' button. The Preset mode will

i 5

ºc

be cancelled and the product will return to normal operation and the

p I

S E T

display will show the current room temperature as shown,

i 5

E I

ºc

7 0

S E T

ºc

2. If you want to set a new setpoint, just rotate the dial until your

required setpoint is shown on the display. After a couple of seconds

i 5

ºc

the display will change to show the current room temperature as

S E T

shown,

i 5

ºc

S E T

ºc

To change the user adjustable settings

• To enter the 'User' menu, press and hold the 'Set' button for

ºc

more than 5 but less than 10 seconds – the display will show 'Pr'

(Preset temperature setting) as shown,

p I

ºc

• If the dial is turned clockwise one click then 'HI' (Maximum

ºc

temperature setting) will be displayed and if turned one more click

clockwise then 'Lo' (Minimum temperature setting) will be displayed.

7 0

ºc

i 0

3 0

ºc

Changing the Preset Temperature

• To adjust the 'Preset' temperature enter the user menu as

i 5

ºc

described above, then rotate the dial until 'Pr' is shown, press the

ºc

SE T

set button and the display will show the current Preset setting.

i 5

ºc

SE T

• Rotate the dial clockwise to increase the Preset temperature

ºc

& anti-clockwise to reduce the Preset temperature. Press the

ºc

'Set' button to conﬁrm and 'Pr' will be displayed.

ºc

Changing the Maximum Temperature Setting

ºc

p I

• To adjust the maximum temperature setting enter the user

ºc

menu as described above, then rotate the dial clockwise until 'HI'

i 0

3 0

ºc

is showing.

E I

ºc

• Then press the 'Set' button, the current setting is shown.

i 0

3 0

ºc

i 0

3 0

ºc

• Rotate the dial clockwise to increase the maximum temperature

ºc

setting (max.30ºC) and anti-clockwise to reduce the maximum

ºc

temperature setting (min 5ºC or min. temp. setting). Press the

'Set' button to conﬁrm, the display will show,

ºc

p I

Changing the Minimum Temperature Setting

i 0

3 0

ºc

• To adjust the minimum temperature setting enter the user

E I

menu as described above, then rotate the dial clockwise until 'Lo'

ºc

Is showing.

p I

ºc

p I

7 0

ºc

E I

• Then press the 'Set' button, the current setting is shown.

E I

ºc

i 5

ºc

SE T

ºc

• Rotate the dial clockwise to increase the minimum temperature

i 5

ºc

setting (max.30ºC or max. temp. setting) and anti-clockwise to

SE T

reduce the minimum temperature setting (min 5ºC). Press the

ºc

'Set' button to conﬁrm, the display will show,

p I

ºc

i 0

3 0

p I

ºc

i 0

3 0

E I

ºc

While adjusting the settings within the menu, when you reach the

ºc

maximum or minimum possible setting the display will ﬂash to

ºc

indicate you cannot adjust the product further, e.g. you cannot set

ºc

p I

the Preset higher than the maximum temperature setting.

ºc

p I

7 0

ºc

To return to normal operation, either press the 'Set' button for

more than 5sec or wait for 1 minute and it will return automatically.

ºc

i 5

ºc

SE T

7 0

i 0

3 0

ºc

7 0

ºc

i 5

ºc

SE T

i 5

ºc

p I

i 5

ºc

SE T

ºc

p I

S E T

i 5

ºc

E I

i 5

ºc

SE T

E I

S E T

7 0

ºc

i 0

3 0

ºc

TAMPER PROOFING (All Models)

To tamper proof the product i.e. prevent unauthorised adjustment of

the product set the Min and Max temperatures to the same desired

value.

FAULT DIAGNOSIS (All Models)

If the display shows E1, the following faults could have occurred

p I

1. Internal temperature sensor has failed.

2. Ambient temperature is outside product operating temperature range.

E I

BATTERY REPLACEMENT (All Models)

• When the batteries are getting low (approx 30 days battery

life remaining) the battery symbol will ﬂash in the display, it is

recommended to change the batteries during this period.

• After approx 30 days, a continuous battery symbol only will be

shown in the display and the unit will remain OFF.

p I

How to replace the batteries

Remove battery

compartment

7 0

ºc

i 5

ºc

SE T

i 5

ºc

Remove the battery compartment by pinching the tabs and

SE T

withdrawing downwards. Replace the spent batteries with 2 x AA 1.5V

alkaline batteries ensuring correct orientation. Replace the battery

compartment pressing fully home.

RF PRODUCT ONLY

SCR RECEIVER (RF Model only)

SCR (Receiver) Normal Operating Mode

• Once the 'Wireless System' has been commissioned, there should

be little need for any user interaction with the SCR.

• During normal operation the red and green LEDs will occasionally

be on, these signify the following;

Green LED

The green LED will be on when there is a demand for heating, and

off when there is no demand.

Red LED

The red LED will ﬂash for 7 seconds, approximately every 5

minutes. This denotes that a radio signal is being received from

the Digistat+RF unit.

Situations Requiring Attention

Red LED continually ﬂashing

• This denotes that the batteries in the Digistat+RF unit are

approaching the end of their life (see 'battery replacement').

Red LED continually on

• This denotes that the SCR has been unable to receive a radio

signal from the Digistat+RF unit. This may be caused by the

batteries being dead (see 'battery replacement') or some

temporary interference with the radio signal.

• To resend and test the signal, go to the Digistat+RF unit and open

the battery drawer, after a few seconds (the display will go blank)

close the battery drawer and then reset to your desired

temperature. If the radio signal has been successfully transmitted

and received, the red LED will ﬂash for 7 seconds then go off.

• If the red LED stays on, there may be some other fault that will

require the attention of a heating engineer/electrician.

Manual Overide

• The heating can be manually switched on and off by using the

'OVERRIDE' button on the SCR in a fault situation, even though

the red LED will stay on until a satisfactory signal is reinstated.

• Once the SCR receives a satisfactory signal again, it will

automatically reset itself for normal operation.

RF PRODUCT ONLY

INSTALLATION OF SCR (RF Models only)

RECEIVE / ALARM

OVERRIDE

LEARN

MODE

If you do not have the knowledge to install the SCR safely then you

must arrange for a competent electrician to install it for you. Wiring

must conform to the current IEE regulations.

Prior to commencing the installation you must ensure the mains supply

is switched off.

Installation Instructions

Read all installation and commissioning instructions before

proceeding.

Do not switch on until ready to commission.

The system wiring must be able to be fully disconnected from the

mains supply by a switch incorporated in the ﬁxed wiring having a

contact separation of at least 3mm on both poles. Fused at 3A.

Location

The Digistat SCR (receiver) should be mounted in a convenient

position, close to the combi boiler or central heating system wiring

centre. (Care should be taken not to mount the SCR in a position

where it is surrounded by metal objects or mains voltage cable, as this

may interfere with the radio signal).

For the best performance install in an open space, at least 30cm

distance from any metal objects including wall boxes and boiler

housing.

It is recommended that the SCR is mounted on the wall nearest the

ﬁnal location of the Digistat +RF room thermostat and not less than

30cm from the boiler side panel.

Warning: Installing the SCR too close to the metal side panel or

mains cables may interfere with the radio signal.

30cm Min

�

BOILER

�

SCR

�

Radio Signal Range:

30m Typically

The range may be affected by

composition/density and number of walls

�

Preferred side of boiler

between the Digistat +RF and SCR

Fixing (minimum wall plate clearances shown)

1. Loosen the securing screws, remove the wallplate, and if surface

wiring is to be used, snap out the cable entry strip on the bottom

edge of the wallplate with a pair of pliers.

2. Fix the wallplate, terminals at the top, either direct onto the ﬂat

wall using wall plugs and no 6 x1" wood screws or on a ﬂush

mounting single conduit box using M3.5 x 14 screws. Minimum

wallplate clearances are shown.

3. Complete the wiring to the SCR wallplate in accordance with the

relevant diagram, to comply with current IEE regulations.

4. Place the SCR onto the wallplate and tighten the securing screws.

SCR wallplate clearances

50 mm

minimum

clearance

N L

40 mm

minimum

clearance

70 mm

minimum

clearance

Electrical

Volt free contacts

230V AC 50Hz

Common

Call for

heating

Fused 3A

heat

satisfied

or call for

cooling

This product is double insulated and does not require an earth

connection. The SCR should be wired to the combi boiler or central

heating wiring using the correct type of cable or ﬂex. The SCR should

be wired in to replace hard wired room or programmable thermostats

shown on the system or boiler wiring diagrams. Always check other

manufacturers instructions for compatibility.

Combi boiler basic wiring layout

Switched

Internal

230V AC

boiler

L -

boiler

L -

fused 3A,

electronics

fused 3A,

electronics

External

N -

External

N -

controls

connections

Digistat + RF

SCR

Radio signals

SCR

Radio signals

to SCR - no wiring

Zone control basic wiring layout

Switched live

from wiring

Motorised valve

from wiring

Motorised valve

centre

See

note

To boiler

230V AC

and/or

fused 3A

pump

Digistat + RF

SCR

Radio signals

SCR

Radio signals

to SCR - no wiring

COMMISSIONING THE 'WIRELESS SYSTEM' (RF Models only)

Standard for all models

IMPORTANT: MULTIZONE INSTALLATIONS ONLY

If more than one 'wireless system' is ﬁtted within the same property.

ie. for controlling 2 or more zones (multi-zone) it is essential that the

Digistat RF units are matched correctly to the relevant SCR. This is

easily achieved by commissioning each Digistat and SCR in turn.

1. Install (see installation instructions) and turn power on to the

SCR (receiver). If a separate programmer is ﬁtted, ensure that it is

switched on. The red LED should come on.

2. Push the 'override' button on the SCR once. The green LED should

also come on. Check to see if the boiler and/or motorised valve

are working.

3. To enter 'learn' mode push the button marked 1 followed by 2

(OVERRIDE) and hold both depressed together. The red LED

should ﬂash for 2 seconds and then go out signifying the SCR is in

learn mode. Release both buttons.

4. The red and green LED's should both now be on.

5. Take the Digistat RF and hold it within sight of the SCR (no closer

than one metre).

6. Insert the batteries into the holder and slide them into the Digistat

RF until the drawer clicks into place.

7. The Digistat RF should now display the actual room temperature.

If the unit has been stored in a cold place, it may take time to

warm up.

8. As soon as the battery compartment is slid back into place, the

red LED on the SCR should ﬂash for 7 seconds and then go out.

The green LED may be on or off depending on the room

temperature at the time of commissioning.

9. If the red LED remains on, slide down the battery drawer on the

Digistat RF, check the battery positions are correct, and once the

display has faded, repeat steps 6 to 8.

10. Increase the 'SET' temperature on the Digistat RF by rotating the

dial clockwise until a ﬂame symbol appears, in the left hand

segment of the display.

11. The red LED on the SCR should ﬂash for 7 seconds. This conﬁrms

that the radio signal is being sent and received. After 7 seconds

the red LED should go out and the green one come on.

12. Check to conﬁrm that the boiler and/or motorised valves are

working.

13. Decrease the 'SET' temperature on the Digistat RF by rotating the

dial anticlockwise until the ﬂame symbol disappears.

14. The red LED on the SCR should ﬂash for 7 seconds. After 7

seconds both the red and green LEDs should go out. Check that

the boiler and/or motorised valve have powered down.

15. Place the Digistat RF in the chosen operating position, (see Digistat

RF location section) and repeat steps 10 to 14. Once you have

conﬁrmed the system operates correctly, ﬁt and secure the

Digistat RF to the wall (see installation instructions).

During normal operation the red LED on the SCR will ﬂash for 7

seconds each time a radio signal is received from the Digistat RF. This

will occur approximately every 5 minutes.

The green LED on the SCR denotes a call for heat (ON).

Once the system has been successfully commissioned, buttons 1

and 2 on the SCR should not be pressed simultaneously, unless a

replacement Digistat RF or SCR is ﬁtted.