Electrolux AUCI Посібник - Сторінка 11

Переглянути онлайн або завантажити pdf Посібник для Посудомийна машина Electrolux AUCI. Electrolux AUCI 16 сторінок. Undercounter dishwasher
Також для Electrolux AUCI: Посібник з монтажу, експлуатації та технічного обслуговування (20 сторінок)

Друкувати сторінку

To display the boiler temperature during heating of the

tank, open the door and press the button "J"

(Figure 17).

WASH CYCLES

The wash cycle includes one wash with hot water and

detergent (min 55 °C or min 150 °F for Marine USPH

versions) and one rinse with hot water and rinse-aid

(min 82 °C or min 180 °F for Marine USPH versions).

Table of times

Standard cycle time with supply water at 50 °C.

ZUCI / AUCI / EUCI

EUCIM / EUCAIUSPH

EUCAIWL

EUCAIML

EUCAIMLG

A device lengthens the cycle time if the water in the

boiler has not reached the minimum temperature for

correct rinsing.

The cycle times and the temperature may be persona-

lised (e.g. increase of the rinse time and temperature).

The cycle times should only be set by a specialised

technician.

OPERATION

The filling and heating stage has finished when the

display shows the tank temperature:

55°C

The appliance is then ready for use:

•

Open the door.

•

Pour the required amount of detergent into the tank

(in models without automatic dispenser).

•

Insert the rack containing the dirty dishes.

•

Close the door and select the suitable wash cycle;

the corresponding indicator light comes on and the

wash cycle starts.

Only for models with door lock device

•

A closing device locks the door for the entire dura-

tion of the wash cycle. By pressing the button of the

selected cycle, the cycle is stopped and the door is

released.

•

If the dishwasher is equipped with detergent and

rinse aid level sensors the message

90"

120"

240"

120"

180"

300"

90"

113"

173"

300"

420"

600"

360"

540"

660"

dEt 0

. may

appear on the display. This indicates no detergent

in the external tank.

After 5 cycles performed with a lack of detergent,

the dishwasher inhibits the start of other wash

cycles. Therefore the detergent level in the tank

must be restored (see par. "Manual activation").

•

The lack of rinse aid is signalled by the message

rAi 0

; this message is a warning that does not

stop performance of the wash cycles.

Wash cycles:

- Cycle I

For lightly soiled dishes: press button "J" (Figure 17)

(see table of times).

- Cycle II (recommended)

For normally dirty dishes: press button "H" (Figure 17)

(see table of times).

- Cycle III

For very dirty dishes: press button "F" (Figure 17) (see

table of times).

Only for models with incorporated water softener

If the salt container is empty, the messages

SAL END

are displayed at the start or end of the

cycle. Place the salt in the special container, following

the instructions given in the section "Undercounter

dishwasher with incorporated continuous water softe-

ner".

•

To stop the wash cycle, just press the selected

cycle button or open the door.

•

To continue the wash cycle, just press the selected

cycle button or close the door. The cycle starts

again from where it stopped.

Only for models with door lock device

At the end of the rinse stage the dishwasher carries

out a pause stage of 1 minute 45 seconds, during

which the time remaining for completion of the cycle is

displayed.

This procedure complies with the parameters required by

HTM (Health Technical Memorandum) 2030 guidelines.

In this case door lock hinders door opening, so

washing cycle cannot be interrupted.

SAL 0