Athearn Genesis SD45-2 Інструкція з експлуатації

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Іграшка Athearn Genesis SD45-2. Athearn Genesis SD45-2 2 сторінки.

Друкувати сторінку

Athearn Genesis SD45-2 Інструкція з експлуатації

*Note- The Bell [F1] Dynamic Brake [F6] and

times (do not press F0 2 times or you will shut

Rail-Wheel Clack [F10] can not be played

off the sound). You will then hear the locomotive

simultaneously-the Bell sound will interrupt the

go through it's start up procedure [there will be

other two sounds.

no movement or operating functions for a few

seconds until the locomotive's idle steadies

*Note- Because this locomotive has a dual

out]. Once your locomotive finishes it's start up,

function sound decoder on-board, it does not

it is ready to go to work on your layout.

support CV read back features.

When you are finished running your locomotive,

This decoder supports all program methods

pressing function button 8 [F8] four times will

including: register mode, paged mode, CV pro-

shut your locomotive down. When the locomo-

gramming mode, direct mode, and program-

tive is shut down this way, it will not automati-

ming on the mainv [OPS mode programming].

cally start up next time you need it. You will

Program the locomotive the same way you

have to press any function button 2 times to

would program any other NMRA compatible

re-start it.

decoder with your DCC system.

Once these steps have been completed, fol-

Out Of The Box DCC Running

low the included CV chart to program any new

The first time you run your new SD45-2 loco-

programming features you want into the loco-

motive there are a few steps you should take

motive. When you initially program your new

to make sure the locomotive operates properly:

SD45-2 locomotive, this step should be done

Test the locomotive in it's analog mode

on a program track for best results. You must

[D.C.] if possible. If it runs properly [lights,

know how to properly use your DCC systems

sound, forward and reverse] on D.C., it will

programming mode to program any decoder. If

run trouble free on DCC.

you are unsure of programming a decoder with

The locomotive comes with a factory de-

your system, please consult your DCC systems

fault DCC address of #3. Before program-

instruction book regarding programming or

ming a new address into the locomotive,

contact the manufacturer of your DCC system

test run it on your DCC system on address

for proper guidance.

#3. This will also insure there are no prob-

lems with the locomotive.

Test all functions [lights and sound] on

default address of #3. Use the supplied

Function Chart.

To avoid a current overload on your DCC

system when starting it up with a lot of sound

equipped locomotives on your layout, your new

Athearn Genesis SD45-2 locomotive does not

automatically start up in the DCC mode. To

start the locomotive, in Run Mode, enter the

address you have assigned for the locomotive,

then press any function button [F1-F9] two

Programming for DCC Operation – Digital Mode

This decoder supports all program methods including register mode, paged mode, CV programming, direct mode

and programming on the main (OPS mode programming). Program the locomotive the same way you would pro-

gram any other NMRA compatible decoder with your DCC system.

DESCRIPTION

CV1

Short address

CV2

Start voltage

CV3

Acceleration

CV4

Deceleration

CV5

Top voltage

CV6

Speed curve select (0=linear, 1=slow

increase at slow speed, 2=fast increase

at slow speed)

Page number

CV29

Basic configuration

CV7

Manufacturer Version #

CV8

Manufacturer I.D.

CV17

Long address upper byte

CV18

Long address lower byte

CV19

Advance consist address

CV21

When CV-21=0, all accessory functions will follow

its own address. When CV-21=1, all functions

will follow the consist address

CV49

Sound on/off (0=off)

CV50

Horn type

CV51

Horn volume

CV52

Bell type

CV53

Bell volume

CV54

Bell ring rate

CV55

Diesel rumble volume

CV56

Brake squeal volume

CV57

Dynamic brake volume

CV58

Air release volume

CV59

Air pump volume

CV60

Safety pop valve volume

CV61

Engine cooling fan volume

CV62

Coupling volume

CV63

Random noise volume

CV64

Rail wheel clack

CV105

User identification number

CV106

User identification number

CV112

Light effects

CV113

Coupling fire volume

CV114

Brake release volume

CV115

Auto brake squeal enable/disable

CV116

Coupling sound type

CV118

Random sound enable

CV120

Ditch light flash rate

CV122

Diesel sound type (0=off, 1=rpm & notch synchro

to speed, 2=linear rpm synchro to speed, 3=notch

up/down) ( F8=notch down, F9=notch up)

CV125

Factory default setting: Programming to 1 will

restore all CV's to default setting

Note: Due to the nature of dual function decoders, it does not support the CV read back feature.

The Dual-Function decoder is manufactured by Model Rectifier Corporation for Athearn Trains.

RANGE

FACTORY

VALUE

1-127

0-32

143

192-231

192

0-255

0-127

0-1

0-14

0-3

0-6

1550 Glenn Curtiss Street

0-7

Carson, CA 90746

0-50

0-3

www.athearn.com

0-3

0-255

see chart

0-3

see chart

0-1

1 (enable)

0-2 (0 is off)

0-1

1 (enable)

0-10

0-3

G101 04/14/06

GENESIS SD45-2

WITH DC/DCC

SOUND SYSTEM