Electrolux EIDW6105GS1A Інструкція з монтажу - Сторінка 2

Переглянути онлайн або завантажити pdf Інструкція з монтажу для Посудомийна машина Electrolux EIDW6105GS1A. Electrolux EIDW6105GS1A 2 сторінки.

Друкувати сторінку

6. If levelers need toberemoved, makesurethatthefloorisfreeofall

obstructions.

7. Carefully p lace dishwasher insidecabinet a reasuchthatis

centered i nopening. U secaution when moving dishwasher to

prevent damage tocabinet, dishwasher andfloor.

8. Front o fdoorneeds tobeevenwiththefrontofadjoining cabinets.

Front l evelers s hould allow5/16" below underside o fcountertop

totopof console.

9. Check thatdishwasher is level f romsidetosideby placing a level

against t hetopfrontsection ofthetub. SeeFigure

5a.

_iiii

Figure 5a

10. Check that the dishwasher is level from front to back by taking

out the lower rack, place level on the lower rack wheel support at

the bottom of the tub. See Figure 5b.

11. Adjust levelers up or down until dishwasher is level.

Holes need to be pre-drilled using a #5 drill to secure unit.

12. Screw mounting brackets firmly to cabinet using screws provided

in literature packet. See Image Below.

Figure

13. Open and close dishwasher door slowly. Ensure that there is

clearance to the console.

Adjust accordingly until door opens

and closes freely.

Property Damage

Do not solder within 6" of the water inlet valve. Damage to

the plastic parts in the valve may occur.

Use care that no sealer, dirt, or other objects enter the valve.

Damage to the filter screen may occur.

Be sure the dishwasher

is placed where the water inlet

valve will be kept from freezing.

If the valve freezes, it may

rupture and flooding

may occur.

Water Line

Flush water line before connecting it to water inlet valve to

prevent early clogging of filter screen. Place a bunched towel

over end of line to prevent splashing. Open water supply valve for

a few seconds and let water drain into a pan. Turn off water

supply at shut-off valve.

Route water line to water inlet valve as shown in Figure 4.

While firmly pulling water supply line into 90° elbow, tightly

connect water supply to water inlet valve. Supply line must be

free of kinks, scales, chips, and lubricants.

Turn on water supply and check for leaks.

Electrical Supply

Remove junction boxcoverand

pull housewiring

into junction

box. See Figures Below.

Use a UL listed conduit connector (not included) at box to

stabilize wiring.

Connect incoming black lead to dishwasher's black lead,

incoming white lead to dishwasher's white lead and incoming

green lead to dishwasher's green lead with wire nuts. (See

Grounding Instruction Warning). Wire nuts must be tight.

Green

Wire

to Green Wire

(Ground)

Junction

Box

Junction'

Box Cover

Figure 6a

Wire

to Black Wire

(Hot)

White

Wire

to White

Wire

(Neutral)

Replacejunction

box cover.

Cabinet

Attach

Clip

Cabinet

Seal

Cabinet

Seal

Leveling

Leg

Water

Line

Figure

Electrical

Line

check these items:

Water and electrical lines are straight out in front of the

dishwasher.

All four leg levelers are positioned properly.

Cabinet Seals are positioned on the sides and top of the

dishwasher.

Cabinet Attachment Clips are attached to the cabinet on

both corners on top of the dishwasher.

Replace Toe and Kickplate.

Note: When replacing

Toe

and Kickplate hand tighten screws.

Electric Shock Hazard

Grounding Instructions:

The dishwasher must be connected to a grounded metal,

permanent wiring system or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the appliance's equipment grounding terminal

or lead. It is the consumer's

responsibility

to contact a

qualified installer to make sure the electrical installation

conforms with the National Electrical Code and local codes

and ordinances.

Do not connect the dishwasher to the power supply until the

appliance is permanently

grounded.

All wiring connections must be enclosed in the junction box.

This unit has copper lead wires.

Joining aluminum building wire to stranded copper wire

should be done by a qualified electrician using materials

recognized by UL and local codes.

Do not use an extension cord. Such use can result in fire,

electrical shock, or other personal injury.

Failure to follow these instructions

could result in death or

serious injury.

Review Figures

7, 8 and 9 to see the different ways to connect

dishwasher to drain system. Choose method that best suits

yourneed.

Entry Must be

.y.

Branch

Tailpiece

Sink at Left

Figure

Sink at Right

2" Drain Hose Hole

The drain hose loop must be at least 32" high from the noor

to insure proper drainage.

If you connect to a sink drain, entry will need to be above trap.

A "Y" branch tailpiece and connector kit, not included, will make

this method easier and includes all needed fittings and

instructions. See Figure 7.

If you connect to a sink trap, local codes may require you to

install an air gap kit, (not included). The drain hose will be routed

from dishwasher to air gap inlet as shown in Figure 8. An air

gap kit is available from a plumbing supply store. (If the drain

hose is installed through the floor, an air gap is necessary).

If you connect to a disposer, the large end of drain hose will fit.

Figure 9(a). The knock out plug must be removed from

inside disposer inlet before making the final fit to drain

hose. See Figure 9(b).

Cut for 5/8"

connection.

Larger end

fts disport

inlet fitting.

Drain

Hose

Figure

9(a )

cut for 3/,_ " conn_tion.

Drain Air Gap

Sink at Left

Disposer

Figure

9(b)

Drain

__ [_

Through

Floor into

Separate

- -L

Trap

Sink at Right

2" Drain Hose Hole

The drain hose loop must he at least 32" high from the floor

to insureproper drainage.

If the cabinet wall is wood, sand edges of hole until smooth and

rounded. If cabinet wall is metal, cover all sharp edges with

electrical or duct tape to avoid cutting drain hose.

Move unit back in place while routing drain hose through access

hole. Use caution to prevent damage to the dishwasher, floor and

cabinets. IMPORTANT:

Make sure there are no sharp bends

or kinks that might restrict drain flow.

Secure drain hose to sink drain, disposer, or separate trap with a

clamp. IMPORTANT:

Be careful not to overtighten clamp or

you may damage end of hose. Do not connect hose to

horizontal pipe between sink drain and disposer.

Be sure unit does not rest on drain hose. tt should be free of

electrical components and door springs. Do not cut corrugated

drain hose. Pull excess through cabinet and place under sink.

Make sure hose does not come in contact with any sharp edges.

Electric Shock Hazard

Disconnect electrical

power at the fuse box

or circuit breaker box before beginning

installation.

Failure to follow this warning could result in

death or serious injury.

Cut Hazard

Metal color panels are sharp and should be

handled with care. Wear gloves to protect

hands.

Failure to follow this warning may result in

injury.

Electric Shock Hazard

If all connections are correct, there are no leaks,

and unit runs properly, replace the kickplate

assembly before placing unit into operation.

Failure to follow this warning could result in

electric

shock.

check these #ems:

Water and drain lines have no kinks and move freely

behind the dishwasher.

Water supply is turned on.

Joints are free of leaks.

Wiring connections to junction box are tight all access

panels are secured back in place.

Replace kickplate. See Figure 1

Drain hose is assembled to Drain Hose Connector.

All packing materials and consumer literature have

been removed from inside unit.

Dishwasher is level and securely fastened.

Open and close door to make sure it does not hit

surrounding cabinet or countertop.

Make sure that all wire ties are removed from the Adjustable

Rack Assembly, Versa Tray, Utility Tray and Silverware

Baskets.

Operate the machine through at

least one fill and pump-out,

checking the following items:

On EWDW6505 press and hold SET Icon for 5 seconds

before first use. On EIDW6305 and EIDW6105 press and

hold down HI-TEMP Icon for 5 seconds before first use.

At first fill, approximately 2 minutes make sure water

completely covers filter surface.

At pump-out: (pump-out is either when the cycle is

completed or canceled, refer to the Use and Care Manual

for Start/Cancel), make sure all water is pumped out.

Check water connections again for leaks.