AND SCE-27 Інструкція з експлуатації - Сторінка 2

Переглянути онлайн або завантажити pdf Інструкція з експлуатації для Обладнання для запису AND SCE-27. AND SCE-27 2 сторінки. Bluetooth communication interface for sc/se

Друкувати сторінку

SCE-27 Bluetooth

Communication Interface for

is a wireless communication option. Attach to the

SCE-27

Installation Procedure

Note:

Before installing the SCE-27 option board,

be sure to remove the batteries from the scale.

Step1

Hold the board in such a way that its LED will

match the hole on the casing. Insert the board

into the casing by sliding it into the casing groove.

Step2

Place the waterproof packing on the casing,

aligning its holes with the casing screw holes.

Step3

Remove the four screws on the option slot

panel located on the bottom right of the display.

Step4

Connect the option board

to the connector on the display unit.

Step5

Secure the casing to the display, using

the four screws provided with the casing.

Step6

Seal the screw heads with the tabs

attached to the waterproof packing.

2. Connectable device

□

AD8931

：Wireless Remote Display

□

AD8541-PC

：Wireless Communication Interface for PC

(Connect to USB port of computer)

Note1 Refer to the A&D website for details.

□

Smartphone / Tablet / PC with Bluetooth

□

：Refer to 5- HID function.

Note2 Turn on DIP switch No.1.

DIP switch

Refer to 3- DIP switch.

3. DIP switch

DIP switch

Case

No.1

SELECT

OFF

Two-way

communication

(Factory Setting)

Keyboard input

SC/SE

INSTRUCTION MANUAL

series scale.

SC/SE

Output Data

No.2

SERIAL

OFF

Connect to AD8931 or AD8541-PC

OFF

Only numerical data

header, no +sign and no unit

(No

1.23

Example 1)

－4.56

Example 2)

Data

4. Setting the scale (SC/SE series)

Refer to the instruction manual of the scale (SC/SE series), to set the functions.

－ Set function "bp5" to " 0".

－ Set function "prt" to " 0".

5. HID function (HID Over GATT Profile)

□

□ By turning on DIP switch No.1, you can connect to a Smartphone, tablet, or PC with Bluetooth and use a

general-purpose text application or spreadsheet software.

□

□ The output data has no header (ST, WT, etc.), + sign and unit (g, kg, etc.).

□

□ Set the keyboard language of device to English.

Pairing

□ Turn on the Bluetooth function of connection device and power on the scale. Select the "A&D_HID" device and pair.

□

S/N may have been added after "A&D_HID".

□ You will not be able to connect if more than 30 seconds have passed without pairing after selecting the device.

□

In that case, power off the scale and try again.

6. Precautions for use

□ Refer to the instruction manual of the connection device for the pairing.

□

□ The LED lights up when the wireless communication connection is completed.

□

□ It will connect automatically when the paired device is nearby. When connecting to other device, turn off the

□

unused devices or disconnect.

□

□ If you can't communicate, check that the connector is firmly connected. If it still fails, check the scale settings,

pairing and connected devices.

7. Wireless communication

□

□ Bluetooth devices is EYSHCNZXZ (TAIYO YUDEN CO.,LTD.)／Bluetooth 5.0 (Bluetooth Low Energy)

□ The effective range communication is 10 m or less in an unobstructed space.

□

If there is an obstacle such as a wall, the range of communication will be shorter.

□ Interference may be caused near the following devices that use the 2.4 GHz frequency band, which is the same as

□

for Bluetooth. Therefore, this device is not suited for uses that require reliability.

－ Wireless LAN

－ Bluetooth devices (such as mobile phones)

－ Home appliances such as microwave ovens

8. Compliance

8-1. Compliance with FCC Rules

This device contains transmitter module FCC ID : RYYEYSHCN

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions :

(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. (FCC = Federal Communications Commission in the U.S.A.)

FCC warning

Changes or modification not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to

part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his / her own expense.

8-2. IC

IC RADIATION EXPOSURE STATEMENT FOR CANADA

)

This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two

conditions : (1) this device may not cause interference, and (2)this device must accept any interference, including

interference that may cause undesired operation of the device.

This device contains transmitter module IC : 4389B-EYSHCN

- 2 -

(In case of connection to AD8931)