CARP PRO Q5 Посібник користувача - Сторінка 2
Переглянути онлайн або завантажити pdf Посібник користувача для Система безпеки CARP PRO Q5. CARP PRO Q5 2 сторінки. Bite alarm set
Друкувати сторінку
CARP PRO Q5 Bite Alarm Set
1.
Install the battery. The horn will beep.
2.
Power on. Press the Function button and hold down for 2 sec. All the lights will flash once and the horn will beep.
3.
Volume adjustment. Rotate V wheel to adjust the volume. Rotation clockwise increases the volume, rotation counterclockwise decreases it. 6
levels of volume are available to adjust. The row of the light indicators indicates the level of volume.
4.
Tone adjustment. Rotate T wheel to adjust the tone. 6 types of tone are available to adjust. The row of the light indicators indicates the type of
tone.
5.
Sensitivity adjustment. Rotate S wheel to adjust the sensitivity. 6 levels of sensitivity are available to adjust. The row of the light indicators
indicates the level of sensitivity when adjusting. 1 indicator means maximum of sensitivity, 6 indicators mean minimum of sensitivity.
st
6.
Function button: 1
click – night light on, 2
lights up only in the dark because the alarm is equipped with a photo-sensor. These allow to save the charge of the battery.
7.
Low voltage alarm. The Function button backlight will flash. Replace the battery as soon as possible.
8.
Drop-back function. The alarm indicates drop / back bites with different sounds and running light of different directions.
9.
Memory function. White and colored light indicators light up for 15 sec after a bite. If the bite was back from the alarm the colored indicator
flashes.
10. Power off. Press and hold down the Function button for 2 sec. The horn will beep.
1.
Install the batteries. The horn will beep.
2.
Power on. Press black Function button and hold down for 2 sec. All the indicator lights will flash, and the horn will beep.
3.
Volume adjustment. Adjust the volume with the V+ and V- buttons. 5 levels of volume + vibration mode are available to adjust.
4.
Tone selection. Tone selection. When the device is in standby mode the alarm tone of the receiver is synchronized with the alarm tone.
5.
Night light function. Press white Function button and hold down for 2 sec to turn on / off night light mode.
6.
Remote control of alarms. Press black Function button. The red indicator light (corresponding to the red indicator) and V indicator light will
light up, the backlight of the white Function button will flash. Adjust the volume of the red alarm with the V+ and V- buttons. Press black
Function button to adjust other alarms. Press black Function button and white Function button. The red indicator light (corresponding to the
red indicator) and T indicator light will light up, the backlight of the white Function button will flash. Adjust the tone of the red alarm with the
V+ and V- buttons. Press black Function button to adjust other alarms. Press black Function button once and white Function button two times.
The red indicator light (corresponding to the red indicator) and S indicator light will light up, the backlight of the white Function button will
flash. Adjust the sensitivity of the red alarm with the V+ and V- buttons. Press black Function button to adjust other alarms. You can exit this
mode if there is no operation within 20 seconds.
7.
Test mode. Press black Function button 5 times to turn on the test mode. Blue light indicator in the left corner will light up. In this mode, every
13 seconds the communication with the alarms is checked. The indicator lights corresponding to the activated alarms flash alternately. Press
the black Function button to exit the mode.
8.
Anti-theft function. For turn on / off the function: press black Function button; then press white Function button and hold down until the horn
beeps.
9.
Synchronization. Press the button located on the top of the back of the receiver with the use of the needle. The first (red) indicator will light
up. If you need to synchronize the signal with the red alarm, rotate its roller – the receiver will receive the signal and synchronize with the
alarm. The horn will beep. Press the button to select other alarms . You can exit this mode if there is no operation within 10 seconds.
10. Drop-back function. Drop: the indicator light corresponding to the alarm and the indicator light in the left corner (red) will light up. Back: the
indicator light corresponding to the alarm and the indicator light in the left corner (blue) will light up. Moreover drop / back bites are indicated
with different sounds.
11. Low voltage alarm. The light indicator in the left corner will flash. Replace the battery as soon as possible.
12. Power off. Press black Function button and hold down for 2 sec. The horn will beep.
Batteries: 6F22 (9 V) – alarms, 2xAAA (1.5 V) – receiver. Wireless receiving working frequency: 433.92 MHz. Effective operation distance of
wireless receiver: 250 m
If you don't use the devices for a long time, please take out the battery!
USER MANUAL
Bite Alarm
nd
click – anti-theft system on, 3
Receiver
Specifications
rd
th
click – night light off, 4
click – anti-theft system off. Night light
ENGLISH