Bosch GBM Professional 13-2 RE Оригінальна інструкція з експлуатації - Сторінка 9
Переглянути онлайн або завантажити pdf Оригінальна інструкція з експлуатації для Дриль. Bosch GBM Professional 13-2 RE. Bosch GBM Professional 13-2 RE 13 сторінок. Rotary drill
Також для Bosch GBM Professional 13-2 RE: Інструкція з експлуатації Посібник з експлуатації (6 сторінок)
Друкувати сторінку
OBJ_BUCH-321-002.book Page 19 Tuesday, November 17, 2009 9:01 AM
Declaration of Conformity
We declare under our sole responsibility that
the product described under "Technical Data" is
in conformity with the following standards or
standardization documents: EN 60745 accord-
ing to the provisions of the directives
2004/108/EC, 98/37/EC (until 28 Dec 2009),
2006/42/EC (from 29 Dec 2009).
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Dr. Egbert Schneider
Dr. Eckerhard Strötgen
Senior Vice President
Head of Product
Engineering
Certification
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
04.11.2009
Assembly
Auxiliary Handle
(GBM 13-2/GBM 13-2 RE)
(see figure A)
Operate your machine only with the auxilia-
ry handle 10.
The auxiliary handle 10 can be set to any posi-
tion for a secure and low-fatigue working pos-
ture.
Turn the bottom part of the auxiliary handle 10
in counterclockwise direction and swivel the
auxiliary handle 10 to the desired position. Then
retighten the bottom part of the auxiliary handle
10 by turning in clockwise direction.
Adjusting the Drilling Depth
The required drilling depth X can be set with the
depth stop 11.
Press the button for the depth stop adjustment
9 and insert the depth stop into the auxiliary
handle 10.
Bosch Power Tools
The knurled surface of the depth stop 11 must
face downward.
Pull out the depth stop until the distance be-
tween the tip of the drill bit and the tip of the
depth stop correspond with the desired drilling
depth X.
Changing the Tool
Before any work on the machine itself, pull
the mains plug.
Wear protective gloves when changing the
tool. The drill chuck can become very hot
during longer work periods.
Keyless Chuck (see figure B)
Hold the rear sleeve 3 of the keyless chuck 1
tight and turn the front sleeve 2 in rotation di-
rection
, until the tool can be inserted. Insert
the tool.
Hold the rear sleeve 3 of the keyless chuck 1
tight and firmly tighten the front sleeve 2 by
hand in rotation direction
action (click) is heard. The drill chuck is locked
automatically.
The locking is released again to remove the tool
when the front sleeve 2 is turned in the opposite
direction.
Key Type Drill Chuck (see figure C)
Open the key type drill chuck 14 by turning until
the tool can be inserted. Insert the tool.
Insert the chuck key 13 into the corresponding
holes of the key type drill chuck 14 and clamp
the tool uniformly.
Screwdriver Tools (GBM 10-2 RE/
GBM 13-2 RE) (see figure D)
The drill spindle 16 is equipped with a hexagon
socket for use with screwdriver bits. Dismount
the drill chuck and insert the screwdriver bit 15
directly into the drill spindle 16 where it is re-
tained by a securing ring.
1 609 929 V00 | (17.11.09)
English | 19
, until the locking