Andrew Type 960 Class I & II Інструкція з монтажу Посібник з монтажу - Сторінка 7
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Антена Andrew Type 960 Class I & II. Andrew Type 960 Class I & II 9 сторінок. Antenna system
Друкувати сторінкуEARTH STATION ANTENNA AZIMUTH (IN DEGREES)
EARTH STATION ANTENNA AZIMUTH (IN DEGREES)
11
ASSEMBLY AND INSTALLATION
FEED AND FEED LEG INSTALLATION
NOTE: Long formed end of Side Feed Leg attaches to
the Reflector rim, short formed to side of Feed Support
Terminal.
Assemble Bottom Feed Leg to bottom of Reflector rim.
From the inside of Reflector rim, insert M6 x 16mm Hex
Bolt thru hole in rim and attach Bottom Feed Leg. Secure
with Lock Washer and Hex Nut.
NOTE: Bottom Feed Leg is the one with slight bend, with
lance, on one end, and is shorter than the Side Feed
Legs.
Leave all hardware loose. Insert Bottom Feed Leg end
with lance into socket hole in center of Feed Support
Terminal. Twist to engage lances. Attach left and right
Feed Support Legs to Feed Support Terminal, securing
with M6 x 16mm Hex Bolts and Lock Washers. Refer to
Instruction for Feed Assembly to assemble Feed
Assembly and ODU to Terminal Block. Tighten and
torque all hardware to Terminal Block and Reflector to
4 ft-lbs (5.4 N-m). Tighten two screws in Terminal Block
socket equally.
FEED AND FEED SUPPORT TUBE INSTALLATION
MEDIUM DUTY
Assemble "U" Clip to bottom of Reflector using M6 x
22mm Round Head Square Neck Bolt, Lock Washer and
Hex Nut. Insert bottom Feed Support Tube into "U" Clip
and secure with M6 x 55mm Round Head Square Neck
Bolt and elastic Lock Nut. (Ref. Fig. 1.5 & 1.6) Assemble
Feed Support Block (supplied with Feed package) to
Feed Support Tube, using two M6 x 16mm Hex Bolts and
Lock Washers.
96cm System (Ref. Fig. 1.5)
Attach Side Feed Legs and Braces to left and right
sides of Reflector using M6 x 20mm Hex Bolts, Lock
Washers and Hex Nuts. (NOTE: Long formed end of
Feed Leg attaches to Reflector. Short formed end of
Brace attaches to inside of Reflector rim.) Attach flat-
ten end of Brace to top of Mount Housing using M6 x
22mm Round Head Square Neck Bolts, Tooth Lock
Washers, Flat Washers and Hex Nuts. Round Head
Square Bolt fits on the underside of Mount Housing
top, flatten end of Brace on top side of Mount
Housing, Tooth Lock Washer on top of flatten end of
Brace, then Flat Washer and Hex Nut.
Attach Side Feed Legs to support Block using M6 x
20mm Hex Nuts and Lock Washers. Leave all hard-
ware loose.
ROUND HEAD SQUARE
NECK BOLT (2 REQ)
MOUNT
EXTENSION
ASSEMBLY
PLATE
LOCK WASHER
(2 REQ)
HEX NUT
(2 REQ)
FIG. 1.3 - Installation of Extension Plate to AZ/EL
Housing (1.2m medium Duty Only)
HEX BOLT
FLAT WASHER
HEX NUT
(2 REQ BOTH SIDES)
SIDE FEED LEG
(2 REQ)
HEX BOLT
FLAT WASHER
(2 REQ BOTH SIDES)
FEED HORN/FEED ASSY
w/FEED SUPPORT
BLOCK
FEED SUPPORT
TERMINAL
BOTTOM FEED
LEG
HEX BOLT
LOCK WASHER
(2 REQ)
HEX BOLT
LOCK WASHER
HEX NUT
FIG. 1.4 - Installation of Feed/Feed Support Legs
to Antenna (Light Duty, 96cm Shown)
RD HD SQ NK BOLT
BRACE (1 L.H.
TOOTH WASHER
TOOTH
& 1 R.H.)
FLAT WASHER
WASHER
HEX NUT
(2 REQ)
M6 x 20mm
HEX BOLTS
LOCK WASHERS
HEX NUTS
(2 REQ-BOTH SIDES)
HEX BOLT
FLAT WASHER
(2 REQ)
SIDE FEED LEG
(2 REQ)
BOTTOM FEED
SUPPORT TUBE
MOUNTING
BLOCK
HEX BOLT
RD HD SQ
LOCK WASHER
NK BOLT
(2 REQ)
FLAT WASHER
"U" CLIP
LOCK WASHER
HEX NUT
RD HD SQ
NK BOLT &
ELASTIC LOCK
NUT
FIG. 1.5 - Installation of Feed/Feed Support Legs
to Antenna (96cm Medium Duty)
6