Electrolux CS910CS Посібник користувача - Сторінка 4

Переглянути онлайн або завантажити pdf Посібник користувача для Вентиляційна витяжка Electrolux CS910CS. Electrolux CS910CS 6 сторінок.

Друкувати сторінку

INSTALLATION

Fig. 11

7. Electrical connection

Check that the installation complies with the standards

of local building, gas and electrical authorities. Before

connecting to the mains supply ensure that the mains

voltage corresponds to the voltage on the rating plate

inside the rangehood.

Installation of telescopic flue covers

Separate the inner and outer flue covers, and carefully

remove the protective coating from both. Carefully

reassemble the upper and lower flue covers sections by

sliding the inner into the outer flue cover. Carefully lower

the assembled upper and lower flue covers onto the top

of the rangehood body, and insert the flue cover into the

rangehood body approximately 5mm. Fix upper flue cover

to the wall mounting bracket with screws supplied. Ensure

that the upper section is extended.

User manual_CS910CS

CAUTION

Care must be taken to ensure the screws are not cross threaded when

attaching the upper flue cover.

If installed in recirculating mode, insert the optional carbon

filter (included in recirculation kit AR910RK).

To complete the rangehood installation, insert the three

filters to the underside of the hood body. Place back edge

of filter into position and push up front edge so that the

filter clips into place.

Your Westinghouse rangehood is now ready to use.

CONTROL PANEL

• Best results are obtained by using a low speed for

normal conditions and a high speed when odours are

more concentrated.

• Turn the hood on for a few minutes before you

start cooking.

• The hood should be left on for 15 minutes after cooking

or until all odours have dispersed.

• The control switches are located on the front panel of the

unit. See

Fig. 12 below.

Fig. 12

• The control panel comprises of:

– T: Indicator lamp

– U: Light button

– V: Off button

– W: 3 control switches for the motor

(speed positions 1, 2, and 3)

CARE & MAINTENENCE

CAUTION

External surfaces are susceptible to scratches and abrasions, so

please follow the cleaning instructions to ensure the best possible

result is achieved without damage.

Cleaning the hood

• Clean the outside of the hood using a damp cloth and

a solution of water and mild washing up liquid. Clean

stainless steel surfaces using non-abrasive cleaning

products that are specifically for use on stainless steel.

To ensure best results also use an even pressure and

follow the grain of the stainless steel. Use of a soft cloth

reduces the risk of scratching. If the cloth is wet ensure

that a dry soft cloth is used to wipe down the surface

again reducing the risk of any surface rust appearing.

• Never use corrosive, abraisive or flammable cleaning

products or products containing bleach.

• Never insert pointed objects in the motor's

protective grid.

• Only ever clean the switch panel and filter grill using a

damp cloth and mild washing up liquid.

• It is extremely important to clean the unit and change the

filters at the recommended intervals. Failure to do so will

cause grease deposits that could cause a fire.

Removing the metal grease filters

• Push the grease filter towards the back of the unit and

then pull it down and out.

Hand washing

Soak grease filters for about one hour in hot water with a

grease-loosening cleaner, then rinse off thoroughly with hot

water. Repeat the process if necessary. Refit the grease filters

when they are dry.

Dishwasher

Place grease filters in the dishwasher. Select the most

powerful washing program and highest temperature, at

least 65°C. Repeat the process. Refit the grease filters when

they are dry. When washing the metal grease filter in the

dishwasher a slight discolouration of the filter can occur, this

does not have any impact on it's performance.

NOTE: The metal grease filters must be removed and washed,

either by hand or in the dishwasher, every four weeks.

• Clean the inner housing using a hand hot solution only

(never use caustic detergents, abrasive powders or brushes).

Charcoal filter

• The charcoal filter should only be used if you want to use

the hood in the recirculation function.

• This filter cannot be cleaned or re-used and as a general

rule, the activated charcoal filter should be changed once

every four months.

Fitting the charcoal filter

Fit one charcoal filter on the left and one on the right so as

to cover the plastic grids that protect the fan wheel.

• Always specify the hood model code number and

serial number when ordering replacement filters. This

information is shown on the registration plate located on

the inside of this unit.

• Replacement charcoal filters can be ordered from your

local Service Centre.

28/11/2012