Bosch PSR 12-2 Оригінальна інструкція з експлуатації - Сторінка 9
Переглянути онлайн або завантажити pdf Оригінальна інструкція з експлуатації для Дриль. Bosch PSR 12-2. Bosch PSR 12-2 14 сторінок.
Також для Bosch PSR 12-2: Оригінальна інструкція з експлуатації (13 сторінок)
Друкувати сторінку
OBJ_BUCH-596-001.book Page 9 Wednesday, November 14, 2007 8:11 AM
Changing the Tool (see figure A)
Before any work on the machine (e. g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational di-
rection switch to the centre position. Unin-
tentional actuation of the On/Off switch can
lead to injuries.
Hold the rear sleeve 3 of the keyless chuck 1 tight
and turn the front sleeve 2 in rotation direction
, until the tool can be inserted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight
and firmly turn the front sleeve 2 in rotation di-
rection
by hand.
The locking is released again to remove the tool
when the front sleeve 2 is turned in the opposite
direction.
Replacing the Drill Chuck
Before any work on the machine (e. g., main-
tenance, tool change, etc.) as well as during
transport and storage, set the rotational di-
rection switch to the centre position. Unin-
tentional actuation of the On/Off switch can
lead to injuries.
Removing the Securing Screw (see figure B)
The keyless chuck 1 is secured with a securing
screw 12 against unintentional loosening from
the drill spindle. Completely open the keyless
chuck 1 and unscrew the securing screw 12 in ro-
tation direction
. Please note that the securing
screw has a left-hand thread.
Removing the Drill Chuck (see figure C)
Clamp the short end of an Allen key 13 into the
keyless chuck 1.
Place the machine on a stable surface (e.g. a
workbench). Hold the machine firmly and loosen
the keyless chuck 1 by turning the Allen key 13 in
rotation direction
. Loosen a tight-seated key-
less chuck by giving the long end of the Allen key
13 a light blow. Remove the Allen key from the
keyless chuck and completely unscrew the key-
less chuck.
Bosch Power Tools
Mounting the Drill Chuck (see figure D)
The keyless chuck is mounted in reverse order.
Note: After mounting the keyless chuck, screw
the securing screw 12 in again.
The drill chuck must be tightened with a
tightening torque of approx. 35–40 Nm.
Dust/Chip Extraction
Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one's health. Touch-
ing or breathing-in the dusts can cause aller-
gic reactions and/or lead to respiratory infec-
tions of the user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in con-
nection with wood-treatment additives (chro-
mate, wood preservative). Materials contain-
ing asbestos may only be worked by
specialists.
– Use dust extraction whenever possible.
– Provide for good ventilation of the working
place.
– It is recommended to wear a P2 filter-class
respirator.
Observe the relevant regulations in your coun-
try for the materials to be worked.
Operation
Starting Operation
Inserting the Battery
Use only original Bosch O-pack batteries
with the voltage given on the type plate of
your machine. The use of other batteries can
lead to injuries and danger of fire.
Set the rotational direction switch 9 to the centre
position in order to avoid unintentional starting.
Insert the charged battery 6 into the handle so
that it can be felt to engage and faces flush
against the handle.
1 609 929 M88 | (14.11.07)
English | 9