Atlantic Boilers RS TURBOFLOW DN 200 S990+ Посібник з експлуатації та обслуговування - Сторінка 7

Переглянути онлайн або завантажити pdf Посібник з експлуатації та обслуговування для Промислове обладнання Atlantic Boilers RS TURBOFLOW DN 200 S990+. Atlantic Boilers RS TURBOFLOW DN 200 S990+ 18 сторінок. Plate heat exchangers

Друкувати сторінку

3 - INSTALLATION

Always read this guide carefully before

working on the

unit and keep it in a safe place for future

reference.

3.1 - Choice of location

The intended location of the unit should be

fully accessible so as

to ease servicing and maintenance

operations and allow easy

removal of the plates from the side of the

unit (Fig. 3). Adequate

clearance must be left in front of the safety

and control devices.

Fig. 3

3.2 - Installation

3.2 - Installation recommendations

recommendations

• CIPRIANI plate heat exchangers have a limited operating

• Atlantic plate heat exchangers have a

pressure and temperature range. Install all the necessary

safety devices to prevent overrunning the limits specified

limited operating

on the order documents. Approval to use the plate heat

pressure and temperature range. Install

exchangers at higher conditions must be obtained from CIP-

all the necessary safety devices to prevent

RIANI. It is recommended to fit pressure and temperature

test points near the unit.

overrunning the limits specified on the

• Make sure that the heat exchanger is compliant with the

order documents. Approval to use the

safety rules in force on the site of use (explosive atmos-

phere, etc.).

plate heat exchangers at higher conditions

• Affix appropriate visual warning sign wherever the surface

must be obtained from Atlantic .

temperature above 60°C or below 0°C.

• If the heat exchanger is to be installed on framework, the

It is recommended to fit pressure and

temperature test points near the unit.

• Make sure that the heat exchanger is

compliant with the

safety rules in force on the site of use

(explosive atmosphere, etc.).

• Affix appropriate visual warning sign

wherever the surface

temperature above 60°C or below 0°C.

• If the heat exchanger is to be installed

on framework, the 35 structure must be

designed to withstand the weight of the

minimum recommended

value (mm)

Model

DN32

700

DN50

1000

DN65

1000

DN100

1500

DN150

1500

DN200

2000

exchanger when in operation (filled) and

with its accessories.

• If necessary, affix the hazard symbol

corresponding to the fluid in accordance

with applicable standards.

• Take all appropriate steps to mitigate

the effects of any significant human,

environmental or financial consequences

of failure.

• Make sure that the heat exchanger is

always installed vertically, stable, and

secured using all its anchorage points. If

necessary, fit additional anchors suitable

for the foreseeable stresses.

• Install drains and vents, shut-off valves,

and fill and drain valves on the pipes so

that the heat exchanger can be serviced

without disrupting the system.

• In the event of seasonal use, drain the

heat exchanger completely to prevent any

risk of freezing or corrosion if a corrosive

fluid is used.

• If accessories are installed on the

heat exchanger, refer to their specific

instructions.

3.3 - Hydraulic connections

• To keep the insides of the pipes clean,

do not remove the seals on their ends until

you are ready to make the hydraulic

connections.

• The insides of the pipes must be free

of all foreign matter (sand, welding slag,

other solid matter, etc.) that could damage

the plates and gaskets.

• Filtration: If the fluids to be circulated

through the heat exchanger contain

suspended matter, a filtration system of up

to 500 μm must be installed.

• Check the tightening dimension

specified on the nameplate. Refer to

section 5.7 if retightening is needed.