Atlantic Technology ICTS-6.2e Інструкція з монтажу - Сторінка 2
Переглянути онлайн або завантажити pdf Інструкція з монтажу для Спікери Atlantic Technology ICTS-6.2e. Atlantic Technology ICTS-6.2e 2 сторінки. In-ceiling theater systems
Також для Atlantic Technology ICTS-6.2e: Інформаційний листок продукту (2 сторінок)
Друкувати сторінку
New Construction and Retrofit Installations
Note: A new construction rough-in kit and back box kit are optionally
available from Atlantic Technology. Please refer to the instructions included
in those kits for their use. If the rough in kit has been used please go directly
to Step 2 below.
Mounting Hole Specifications:
ICTS-6.2e: Diameter = 7-7/8 in., 200mm; Depth = 4-3/8 in., 112mm
ICTS-8.2e: Diameter = 9-5/8 in., 245mm; Depth = 4-7/8 in., 124mm
1
Cut an appropriately sized opening in the ceiling material.Be sure that the
ceiling material can support the weight of the speaker.Also be sure that
the sides of the opening are at least 1-1/2 inches away from any beams or
studs within the cavity. If it is not, the rotating clamps will be restricted
in their movement and may not clamp properly.
2
2
2
Be sure that all foreign material in the ceiling is kept out of the speaker
Be sure that all foreign material in the ceiling is kept out of the speaker
assembly,particularly the back of the woofer cone.(There is a cloth shield
on the rear of the woofer, but please use care anyway.) If the ceiling is
void of insulation it will be beneficial to the performance of the speaker
to install an Atlantic Technology foam Sound Damping Kit behind and
around the assembly.
3
IMPORTANT:
Use the high frequency level adjustment, located on the
tweeter assembly, to increase (+)or decrease (–) the level of high
frequency sound produced by the tweeter. These settings can easily be
changed after the speaker is in stalled. See Figure 1.
4
Attach the previously installed audio feed wires to the speaker terminals.
Simply remove 1/2 inch of insulation from the end of each input wire.
Push down on the terminal connector and a large opening will appear in
the shaft of the connector that is capable of holding up to 10 gauge wire.
Insert the bare wire into the opening and release the terminal. Be sure
to observe correct polarity, connecting the positive (+) leads to the red
terminals and the negative (-) leads to the black terminals.Also be sure
that no stray strands of wire touch across any terminals. See Figure 2.
Figure 2
Specifications
ICTS-6.2e
Frequency Response
55 – 20kHz, +/- 3dB
Sensitivity (1 watt/1 meter) 89dB
Impedance
8 Ω
Woofer type
6½" (165mm) Mica/Graphite loaded
Polymer cone
Tweeters
1" silk dome
Weight
4.8 lbs.
Figure 1
ICTS-8.2e
45 – 20kHz, +/-3dB
89dB
8 Ω
8" (203mm) Mica/Graphite loaded
Polymer cone
1" silk dome
5.25 lbs.
5
5
5
Check to ensure that the rotating clamps are "parked" and not sticking
Check to ensure that the rotating clamps are "parked" and not sticking
out over the edge of the assembly.
6
6
6
Push the speaker assembly straight up into the opening with the tweeters
Push the speaker assembly straight up into the opening with the tweeters
oriented as noted previously.
7
7
7
Tighten the mounting screws one at a time.As you tighten, the rotating
Tighten the mounting screws one at a time.As you tighten, the rotating
clamps on the back of the assembly will turn and lower,until they contact
the back of the ceiling and clamp the ceiling between themselves and the
trim ring. See Figure 3.
Figure 3
8
8
8
Snug all four mounting screws in this manner to make a firm seal with
Snug all four mounting screws in this manner to make a firm seal with
the ceiling. Be careful not to overtighten them.
9
9
9
Start the system and make sure the speakers are operating properly. If
Start the system and make sure the speakers are operating properly. If
necessary, adjust the high frequency switch (on the tweeter assembly,
under the grille) to get the most natural balance of sound throughout
the listening area.
10
0
0
Install the grille by placing it into the recess and pushing it in gently.
Install the grille by placing it into the recess and pushing it in gently.
Atlantic Technology
343 Vanderbilt Avenue Norwood, MA 02062
(781) 762-6300 www.atlantictechnology.com
015-1062-A