Dri-Eaz 2400 Посібник користувача - Сторінка 7

Переглянути онлайн або завантажити pdf Посібник користувача для Осушувач повітря Dri-Eaz 2400. Dri-Eaz 2400 10 сторінок.
Також для Dri-Eaz 2400: Посібник користувача (2 сторінок)

Друкувати сторінку

8. If the DrizAir 2400 shuts off for any reason, allow

five minutes before restarting to avoid compressor

damage.

Warning

If the unit is switched off during use, wait for five (5)

minutes before restarting. Attempting to re-start the

unit before this period of time may cause damage to

the compressor.

MAINTENANCE

Do not attempt to disassemble or repair a dehumi-

difier if you are not qualified to do so. Normal main-

tenance operations and troubleshooting solutions can

be handled by the technician in the field. More com-

plex problems should be handled by an authorized ser-

vice technician. See the Troubleshooting section.

Regular Maintenance

In order to maintain the DrizAir 2400 at optimum

efficiency and to prevent breakdown, the filter must be

cleaned or replaced regularly, and the evaporator and

condenser coils must be cleaned.

The coils are the means by which heat is transferred

between the air stream and the refrigeration circuit.

The coils are critically engineered so that the correct

heat transference takes place and the pressures within

the refrigeration circuit remain within operating limits.

The air passing through the DrizAir 2400 dehumi-

difier may be carrying considerable quantities of dust,

lint and fungus spores. Even using a filter, the coils

may pick up dirt and their heat transferring properties

decrease, resulting in reduced water extraction and un-

due pressure on the components. This is especially true

if the unit is operating in a dusty environment. For op-

timum efficiency, a maintenance schedule should be

set up for checking the coils and the filter at regular

intervals.

Cleaning or Replacing the Filter

Remove the filter from the filter shroud by inserting

a finger into the access hole at the top of the filter

shroud.

When using pleated paper filters, discard the dirty

filter and insert a clean one. If you have difficulty lo-

cating filters of the proper size, replacements are avail-

able from your local distributor. Call Dri-Eaz at 1

(800) 932-3030 for more information.

The DrizAir 2400 is equipped with a cleanable fun-

gal-resistant filter. To clean it use a light vacuum, or

wash with water and mild detergent. Spray directly

against the foam in the direction of the airflow. Begin

at the top of the filter and work down. Allow the filter

to drain dry before reinstalling it in the filter shroud.

Regularly clean or replace the air filter to avoid dam-

age to dehumidifier. Never operate without the air filter

in place.

Cleaning the Coils

The first step in cleaning the coils is directing com-

pressed air, from both sides, through the coils. Ideally,

the coils should be dry and the operation be completed

outside (because of the dust that may be created). After

blowing out loose contamination, a wet cleaning

process may be used.

A thorough cleaning of the evaporator coil can be

performed with an aluminum evaporator coil cleaner

available from a refrigeration service or supply outlet.

Follow the product directions carefully.

If you flush the coil, do not permit water to enter

the electrical compartment. Use a squirt bottle or a sy-

ringe so that you can control the water.

After cleaning the coils, ensure that the drain tray

and drain hose are completely free of dirt. Clean the

front grill with a vacuum cleaner and brush attachment.

Do not attempt to service or clean the dehumidifier

while it is plugged into an electrical outlet. It is dan-

gerous for an unqualified individual to attempt to dis-

assemble or repair the dehumidifier.

Electric Wiring & Cord

Inspect the power cord periodically to ensure insu-

lation is in good condition. Also inspect internal wiring

for abrasions, nicks or cuts. Repair or replace the elec-

tric cord or wiring as needed.

Remove the cover and ensure that all wires are se-

curely fastened and not discolored. (Loose connections

may heat up and show discoloration.) To inspect wir-

ing connections to the touch-pad controls, remove the

four control panel screws, and rotate the entire panel

backward toward you.

Pump Tube

Ensure that the pump tube is not kinked and in good

condition before the DrizAir 2400 leaves for the job

site and again after the installation is completed.

Pump System

Inspect and clean the pump system regularly to

maintain effective operation. Lay the DrizAir 2400 on

its back. The pump is located at the very bottom of the

Warning

Danger